Briggs & Stratton 040220A manual Wire Connections, Before Initial START-UP

Page 17

INSTALLATION

WIRE CONNECTIONS

Recommended Torque Values

Torque all wire connections/fasteners to values recommended in Figure 10. Suitable for copper wire of 60°/75°C rating.

Figure 10 — Recommended Torque Values

CONNECTIONS:

Torque Value

 

 

In Main Distribution Panel:

 

Refer to panel manufacturer specs

 

 

 

In Disconnect Box:

 

 

 

240V AC Utility

5 in-lb

 

 

Engine Start

5 in-lb

 

 

Remote Status

5 in-lb

 

 

Generator

17 in-lb

 

 

Ground

40 in-lb

 

 

Circuit Breakers:

 

Refer to circuit breaker manufacturer specs

 

 

 

Generator AC Connection System

A single-phase, three-wire AC connection system is used in the Home Standby Generator. The stator assembly consists of a pair of stationary windings with two leads brought out of each winding. The junction of leads 22 and 33 forms the neutral lead. A complete schematic and wiring diagram can be found on pages 26-27.

NOTE: Neutral is not bonded to ground at generator.

Grounding the Generator

Ground the Home Generator System per applicable codes, standards, and regulations. The GND lug is located in the disconnect box.

Generator Control Circuit Connection

Control circuit interconnections consist of "240V AC Utility" leads. These two leads must be routed in conduit. Control lead functions are briefly described as follows:

•Leads deliver utility power to generator’s circuit board, oil warmer, optional battery warmer and charge the battery.

Using installer-supplied minimum 300V, 14 AWG copper wire, connect control circuit terminals in the disconnect box to the Transfer Switch.

Remote Diagnostic LED Plate

The light on the remote LED plate is referred to as the Diagnostic LED. The LED will stay lit indicating the generator is in ready mode and will turn on and off in a series of blinks if certain faults are detected in the Home Standby Generator. A mounting plate is supplied so that it can be installed at a convenient indoor location. The owner will use it to observe the status of the Home Standby Generator. Consult with the owner for a convenient location.

To install the remote diagnostic LED plate:

•Mount installer-supplied electrical box to wall.

•Using installer-supplied wire, connect the remote LED leads to the “Remote Status Light” in disconnect box.

NOTE: LED leads are polarity sensitive.

• Attach mounting plate to electrical box.

Refer to the section Fault Detection System for operation.

BEFORE INITIAL START-UP

Engine Oil

This engine is shipped from the factory filled with the recommended oil. Before starting the engine, check oil level and ensure that engine is serviced as described in the engine operator’s manual.

NOTICE

Any attempt to crank or start the engine before it has been properly serviced with the recommended oil will result in equipment failure.

•Refer to engine manual for oil fill information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

Oil Considerations

Your Home Standby Generator is equipped with an engine that has been pre-run at the factory and does not require the traditional “break-in” procedure.

The generator is filled with synthetic oil (API SJ/CF 5W- 30W). This allows for generator operation in the widest range of temperature and climate conditions.

NOTE: The use of synthetic oil DOES NOT alter the required oil change intervals described in the engine operator’s manual.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Rated Watts Home Generator System Table of Contents Hazard Symbols and Meanings Important Safety InstructionsEngine exhaust from this product contains Certain components in this product and relatedSafety Rules Installing the 15A fuse could cause the engine to start Control Panel see BatteryKnow Your Home Standby Generator AUTO/OFF/MANUAL Know Your Control PanelInstallation Assistance Installer ResponsibilitiesIntroduction Customer ResponsibilitiesOwner Orientation Installation ProceduresHome Standby Generator Location Lifting the GeneratorGenerator Clearances General Location GuidelinesDevice Running Watts Essential CircuitsEssential Circuit Selection Disconnect Box Mounting Guidelines Fuel Inlet DimensionsRemovable Roof and Access Door Do not light a cigarette or smoke Gaseous Fuel SystemFuel Consumption Temporary Manometer Installed10ft Fuel Pipe Sizing10ft 15ft 20ft 30ft 40ft 50ft 60ft 70ft 80ft 90ft 100ft Physical Properties Propane Natural Gas Fuel Comparison ChartWithdrawal Rate 32F 20F 10F 30F 40F Before Initial START-UP Wire ConnectionsCharging the Battery Battery ConnectionBattery posts, terminals and related accessories contain Servicing the BatteryInitial START-UP no Load Fuel System SelectionAutomatic Operation Sequence Fuel Supply SystemInstallation Inspection Setting Exercise TimerEngine Cool-down Timer To perform the Set Exercise procedureFault Detection System SpecificationsAutomatic Operation Checking Automatic OperationReset Fault Detection System Fault DescriptionNo LED Discharged Battery Low Oil PressureChanging Engine Oil and Filter Generator MaintenanceChanging Oil Changing Oil FilterStorage To Clean the GeneratorWhen Calling the Factory Problem Cause Correction TroubleshootingDown when loads are connected AvailableSchematic Wiring Diagram Page Limited Warranty Sensor de Excitación de Tensión de la Compañía Tabla DE ContenidoSímbolos de Peligro y Significados AdvertenciaDeterminados componentes en este producto y los Gases Tóxicos Manual de OperarioLos generadores producen un voltaje muy poderoso Instala el fusible se puede producir el arranque del motor PrecauciónEtiqueta del Motor Conozca SU Generador DE ReservaFiltro de Aceite Salida del Escape Manguera de Drenaje de Aceite Etiqueta deDisyuntor Conozca EL Panel DE ControlIntroducción Conserve Estas InstruccionesResponsabilidades DEL Instalador Responsabilidades DEL ClienteProcedimientos DE Instalación Ubicación del Generador de Reserva Elevación del GeneradorDistancias Desde el Generador Pautas Generales para la Ubicación del GeneradorDispositivo Vatiaje de Circuitos FundamentalesSelección de los Circuitos Fundamentales Techo y Puerta de Acceso Desmontables Dimensiones de la Entrada de CombustibleDirectrices de Montaje del Cuadro de Desconexión Sistema DE Combustible Gaseoso Gas Natural Vapor de PL Consumo de CombustibleAl generador de Reserva Propano Líquido PL peso específico = Dimensiones de la Cañería de CombustibleGas Natural peso específico = Tasa de consumo 32F 20F 10F 30F 40F Cuadro de Comparación de CombustiblesPropiedades físicas Propano Gas natural Antes DEL Arranque Inicial Conexiones DE CablesInstale el fusible de 15 Amperios en el panel de control Conexión de la BateríaFije el interruptor AUTO/OFF/MANUAL en la posición Auto Servicio la BateríaArranque Inicial SIN Carga Selección DEL Sistema DE CombustibleSecuencia DE Operación Automática Sistema de Suministro de CombustibleTemporizador de enfriamiento del motor Inspección Posterior a LA InstalaciónOperación Automática EspecificacionesSistema DE Detección DE Fallas Verificación de la Operación AutomáticaLas patillas de las baterías, los terminales y los Cambio del Aceite del Motor y del Filtro Mantenimiento DEL GeneradorCambio del Filtro de Aceite Cambio del AceiteSi Llama a la Fábrica AlmacenamientoPara Limpiar el Generador Reparacion DE Averias Notas Garantía Limitada Table DES Matières Avertissement Symboles de Danger et MoyensVeuillez Conserver CES Instructions NE touchez PAS les fils dénudés ou les boîtiers Avis Filtre à Air Et Jauge dHuile Filtre à lHuile FAMILIARISEZ-VOUS Avec Votre Génératrice D’ÉTAT D’ATTENTEFusible de FAMILIARISEZ-VOUS Avec LE Tableau DE Commande15 Ampères DisjoncteurAide À Linstallation Responsabilités DE LinstallateurConservez CES Instructions IntroductionConseils AU Propriétaire Procédures DinstallationDirectives Générales Concernant lEmplacement Emplacement du Génératrice d’état d’AttenteSoulèvement de la Génératrice Dégagement Autour de la GénératriceAppareil Watts Circuits EssentielsSélection des Circuits Essentiels Toit Amovible et Porte dAccès Dimensions de lOrifice dAdmission du CombustibleDirectives dAssemblage du Boîtier de Débranchement LE Système DE Combustible Gazeux Il faudrait inclure une sortie pour manomètre Consommation de CombustibleVers le génératrice ’état d’attente Gas Naturel Vapeur PLGaz de Pétrole Liquéfié GPL densité = 1,50 Grosseur du Tuyau de CombustiblePropriétés physiques Propane Gaz naturel Charte de Comparaison des Combustibles32F 20F 10F 30F 40F 12,2 C 17,8 C 23,3 C 34,4 C 40 CAvant LE Démarrage Initial Raccords DE FilsRechargez la Batterie Branchement de la BatterieRéglez linterrupteur AUTO/OFF/MANUAL sur Auto Entretien de la BatterieDémarrage Initial Sans Charge Sélection DU Système DE CombustibleSystème dAlimentation en Combustible Réglez linterrupteur AUTO/OFF/MANUAL sur ManualCapteur de Prise en Charge de la Tension de Service Vérification InstallationRéglage DE LA Minuterie DU Cycle Dexercice Minuterie de Refroidissement du MoteurFonctionnement Automatique CaractéristiquesSystème DE Détection DES Pannes Entretien du SystèmeRéarmement du Système de Détection des Pannes Nombre de Clignotements Du VoyantAucun DEL Batterie déchargée Faible Pression dHuileChangement dHuile à Moteur et de Filtre Entretien DU GénérateurVidange de lHuile Changement du filtre à huileCommunications avec le Fabricant RemisagePour Nettoyer le Générateur Dépannage Garantie Limitée

040220A specifications

Briggs & Stratton is renowned for its high-performance engines, and the Briggs & Stratton 040220A is no exception. This powerful engine is designed to deliver reliable performance for a variety of outdoor applications, including lawn mowers, garden tractors, and other small machinery. One of the standout features of the 040220A is its sturdy construction. It is built with high-quality materials, ensuring durability and longevity, even under demanding conditions.

The 040220A is equipped with an overhead valve (OHV) design, which enhances engine efficiency and provides better fuel economy. This technology allows for improved airflow and better combustion, resulting in increased power output while reducing emissions. With its advanced engineering, the engine is capable of delivering consistent performance across a range of applications, making it a versatile choice for both residential and commercial users.

Another important characteristic of the 040220A is its easy starting system. Designed for user convenience, this engine features a user-friendly recoil start mechanism that ensures reliable ignition with minimal effort. This is particularly beneficial for users who value time efficiency and want to avoid the hassle of complicated starting procedures.

The 040220A also boasts impressive torque and horsepower ratings, which contribute to its ability to handle tough tasks with ease. This engine is designed to provide ample power for heavy-duty cutting, mulching, and other demanding applications, ensuring that users can complete their work efficiently.

In addition to its power and performance, the Briggs & Stratton 040220A is also designed with user maintenance in mind. It features easy-access oil fill and drain ports, making routine maintenance tasks straightforward. This attention to user convenience helps ensure that owners can keep their engines in optimal working condition with minimal effort.

Overall, the Briggs & Stratton 040220A stands out as a reliable and powerful engine that incorporates advanced technologies and features aimed at enhancing performance and ease of use. Its robust design, efficient operation, and commitment to user convenience make it an excellent choice for anyone in need of a dependable engine for their outdoor power equipment. Whether you're a DIY enthusiast or a professional landscaper, the 040220A is engineered to meet your needs with proven performance and reliability.
Top Page Image Contents