Murray 624504x4C manual Trouble Shooting Chart, How To Prepare The Snow Thrower For Storage

Page 18

WARNING: For safety and to pro- tect the machine, use only original equipment shear bolts.

To replace a broken shear bolt, proceed as fol- lows. Extra shear bolts were provided in the as- sembly parts bag.

1.(Figure 2) Move the throttle control (13) to the stop position. Disengage all controls.

2.Disconnect the spark plug wire. Make sure all moving parts have stopped.

3.(Figure 9) Lubricate the auger shaft Zerk fitting (1), if equipped, with a grease gun.

4.(Figure 21) Align the hole in the auger with the hole in the auger shaft. Install the new shear bolt (2), spacer (3) and locknut (4).

5.Connect the spark plug wire.

How To Prepare The Snow Thrower For Storage

WARNING: Do not remove gasoline while inside a building, near a fire, or while you smoke. Gasoline

fumes can cause an explosion or a fire.

1.Drain the fuel tank.

2.Let the engine run until it is out of gasoline.

3.Drain the oil from the warm engine. Fill the engine crankcase with new oil.

4.Remove the spark plug from the cylinder. Pour one ounce of oil into the cylinder. Slow- ly pull the recoil-start grip so that the oil will protect the cylinder. Install a new spark plug in the cylinder.

5.Thoroughly clean the snow thrower.

6.Lubricate all lubrication points. See the Main- tenance section.

7.Be sure that all nuts, bolts and screws are securely fastened. Inspect all visible moving parts for damage, breakage and wear. Re- place if necessary.

8.Cover the bare metal parts of the blower housing, auger, and the impeller with spray rust preventative lubricant.

9.Put the unit in a building that has good ven- tilation.

10.If the machine must be stored outdoors, block up the snow thrower to be sure the en- tire machine is off the ground.

11.Cover the snow thrower with a suitable pro- tective cover that does not retain moisture. Do not use plastic.

How To Order Replacement Parts

The replacement parts are shown either on the back pages of this Instruction Book or in a separate Parts List Book.

Use only manufacturer’s authorized or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a PA for purchased assembly. It is important that you include this when ordering a part. Do not use attachments or accessories not specifically recommended for this unit. In order to obtain proper replacement parts you must supply the model number (see nameplate).

ENGLISH

Replacement parts, except for the engine, transmission, transaxle or differential, are available from the store where the product was purchased, a service shop recommended by the store or from a “Murray, Inc. Central Parts Distributor” listed on the back page of this Instruction Book.

If you are unable to obtain parts or service in the manner outlined above, then contact:

USA - MURRAY, INC. Outdoor Power Equipment Customer Service Department P.O. Box 268

Brentwood, Tennessee 37027 1-800-251-8007

CANADA - MURRAY CANADA, INC.

Factory Customer Service

1195 Coutneypark Drive East

Mississauga, Ont. L5T-1R1

1-800-661-6662 Collect telephone calls will not be accepted.

Replacement parts for the engine, transaxle, or transmission, are available from the manufacturer’s authorized service center found in the yellow pages of the telephone directory. Also, see the individual engine or transmission warranties to order replacement parts.

When ordering the following information is required:

(1)The Model Number

(2)Serial Number

(3)Part Number

(4)Quantity

TROUBLE SHOOTING CHART

TROUBLE

CAUSE

CORRECTION

 

 

 

Difficult starting

Defective spark plug.

Replace spark plug.

 

 

 

 

Water or dirt in fuel system.

Use carburetor bowl drain to flush and refill with

 

 

fresh fuel.

 

 

 

Engine runs erratic

Blocked fuel line, empty gas tank, or stale

Clean fuel line; check fuel supply; add fresh

 

gasoline

gasoline

 

 

 

Engine stalls

Unit running on CHOKE.

Set choke lever to RUN position.

 

 

 

Engine runs erratic;

Water or dirt in fuel system.

Use carburetor bowl drain to flush and refill with

Loss of power

 

fresh fuel.

 

 

 

Excessive vibration

Loose parts: damaged impeller

Stop engine immediately and disconnect spark

 

 

plug wire. Tighten all bolts and make all

 

 

necessary repairs. If vibration continues, have

 

 

the unit serviced by a competent repairman.

 

 

 

Unit fails to propel itself

Drive belt loose or damaged.

Replace drive belt.

 

 

 

 

Incorrect adjustment of traction drive cable

Adjust traction drive cable.

 

 

 

 

Worn or damaged friction wheel.

Replace friction wheel.

 

 

 

Unit fails to discharge snow

Auger drive belt loose or damaged.

Adjust auger drive belt; replace if damaged.

 

 

 

 

Auger control cable not adjusted correctly.

Adjust auger control cable.

 

 

 

 

Shear bolt broken

Replace shear bolt

 

 

 

 

Discharge chute clogged.

Stop engine immediately and disconnect spark

 

 

plug wire. Clean discharge chute and inside of

 

 

auger housing.

 

 

 

 

Foreign object lodged in auger

Stop engine immediately and disconnect spark

 

 

plug wire. Remove object from auger.

 

 

 

F-03101 1L

18

 

Image 18
Contents Snow Thrower 03101 1L 1011 03101 1L 03101 1L 03101 1L 03101 1L 03101 1L Contents Product InformationOWNER’S Information International Pictorials StopPreparation Maintenance And StorageTraining OperationAssembly OperationHow To Use The Wheel Lockout Pin Figure How To Go Forward or Backward FigureHow To Throw Snow Figure How To Stop The Engine FigureHow To Remove Snow or Debris From The Auger Housing Figure Snow Throwing TipsMaintenance Chart MaintenanceHow To Check And Adjust The Cables How To Adjust The Height Of The Skids FigureHow To Adjust Scraper Bar Figure How To Adjust The BeltsHow To Adjust The Belt Guide How To Adjust Or Replace The Friction WheelHow To Replace the Auger Shear Bolt Trouble Shooting Chart How To Prepare The Snow Thrower For StorageHow To Order Replacement Parts Sommaire Prise de conscience environnementaleUSA MURRAY, INC Pictogrammes Internationaux Prévenir les blessures duesPoint mort Arrêt moteur Marche Arrêt starter Marche starter Fonctionnement Conseils préliminairesPréparation Entretien et remisageMontage FonctionnementDéblaiement de la neige Figure Arrêt du chasse-neigeFigureAvancer et reculer Figure Utilisation de la goupille de blocage des roues FigureConseils pour l’utilisation du chasse-neige Démarrage d’un moteur à chaud FigureTirer la corde du démarreur 12 au maxi- mum Tableau DE Maintenance EntretienVérification et réglage des câbles Pièces à ne pas lubrifier FigureRéglage du bord d’attaque Figure Réglage des courroiesRemplacement des courroies Réglage ou remplacement du disque de frictionRéglage du guide de courroie Remplacement des pièces détachées ’origine doivent être utilisés pour leur remplacementPréparation du chasse-neige pour le remisage Tableau DE Depannage Consideraciones ambientales Esta Garantía Limitada Murray, Inc. de DosDiagramas Internacionales Prácticas de operación segura para quitanieves rotatorio Ensamblaje OperaciónLanzamiento de la nieve Figura Parada del quitanieves FiguraAvance y retroceso Figura Uso del pasador de bloqueo de la rueda FiguraSugerencias para el lanzamiento de nieve Arranque del motor en caliente FiguraJale la manija de arranque manual 12 lo más afuera posible Tabla DE Mantenimiento MantenimientoAjuste de la barra raspadora Figura Partes que no se deben lubricar FiguraAjuste de la altura de los patines Figura Revisión y ajuste de los cablesCambio de las correas Ajuste de la guía de la correaAjuste o reemplazo de la rueda de fricción Cómo hacer un pedido de piezas de repuesto Reemplazo de los pernos de seguridad de la barrenaPreparación del quitanieves para guardarlo Seguridad originalesTabla DE Localización Y Reparación DE Averías Model 624504x4C Frame Key No. Part No Description 200 Drive229 221 225LF AXLE, Swing Plate YZ Auger Housing Ref. Gear CaseRETAINER, Ball Brng Gear Case Control Panel Handle WASHER, Sptlk Chute ROD Discharge Chute Wheels 676Ref. Drive Shift Yoke Electric Start Assembly 03101 1L 03101 1L 03101 1L MURRAY, INC. Lawn Mower Central Parts Distributors