Emerson PMC-CGM manual Configuration Switches, Cabling and Connectors, Environment

Page 15

Safety Notes

Emerson and our suppliers take significant steps to ensure there are no bent pins on the backplane or connector damage to the boards prior to leaving the factory. Bent pins caused by improper installation or by inserting boards with damaged connectors could void the Emerson warranty for the backplane or boards.

Configuration Switches

Malfunction of the Product

Switches marked as "Reserved" might carry production-related functions and can cause the product to malfunction if their setting is changed.

Therefore, do not change settings of switches marked as "reserved".

Damage of the Product

Setting/resetting the switches during operation can cause damage of the product. Therefore, check and change switch settings before you install the product.

Cabling and Connectors

Product Damage

The RJ-45 connector(s) on the face plate are BITS interfaces. Connecting a telephone to such a connector may destroy your telephone as well as the product.

Make sure that BITS connectors near your working area are clearly marked as network connectors. In addition, observe the following safety notes:

zVerify that the length of an electric cable connected to a BITS bushing does not exceed 100 m.

zMake sure the BITS bushing of the system is connected only to Telecommunication Network Voltage level 1 (TNV-1) circuits.

If in doubt, ask your system administrator.

Environment

Always dispose of used modules, system components and RTMs according to your country’s legislation and manufacturer’s instructions.

PMC-CGM Installation and Use (6806800D53C)

15

Image 15
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C Overview of Contents About this ManualAbbreviations RTM About this Manual Abbreviation DefinitionConventions Notation DescriptionBold Part Number Publication Date Description Summary of ChangesComments and Suggestions About this Manual Notation DescriptionElectrical Interference Safety NotesInstallation Safety NotesOperation Configuration Switches Cabling and ConnectorsEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Schaltereinstellungen Kabel und SteckerUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Description Standard CompliancesStandard Compliances and Clocking Standards Introduction Standard CompliancesOrder Number Description Ordering InformationAvailable Board Variants Ordering InformationIntroductionPage Unpacking and Inspecting the Module Hardware Preparation and InstallationBefore Installation OverviewRequirements Hardware Preparation and Installation RequirementsFeature Value DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature Operating Non-Operating packed stateSwitch Location Configuring the ModuleInstalling and Removing the Module Switch SettingsSwitch Hardware Upgrades and Acessories Installation ProcedureRemoval Procedure Controls, LEDs and Connectors Front Panel Connectors and LEDsLayout Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationAccess Access and Configuration CablingCabling Using a MIB Browser Access and Configuration Using a MIB BrowserConfiguring the PMC-CGM MIB Browser SettingsDefining Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining the IP address of the protection partner moduleConfiguring the Bits interface Configure the Interface ModeConfigure the Bits Interface Configuring the interface modeSetting up a multi-shelf configuration Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Configuring the initial master/slave rolesConfigure the Reference Clock Configuring the reference clock source for the T0/T4 pathConfigure the Reference Clock Access and Configuration Upgrading the firmware/software Perform Firmware/Software UpgradeReset the PMC-CGM Resetting the PMC-CGM via SnmpReset the PMC-CGM Access and Configuration Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmInputTable MIB DescriptionCgmControl MIB StructureInstance CgmInputNumber CgmInputName CgmInputFrequency DefaultInput Assignments MIB DescriptioncgmControlCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl Not supported on PMC-CGM CgmSysCgmEventTable CgmSys MIB DescriptionEvent Codes and Severity MIB DescriptioncgmSysCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistCgmClkDist Objects CgmClkDist MIB DescriptionNot applicable for PMC-CGM PLL Document Title Publication Number Emerson Network Power Embedded Computing DocumentsRelated Specifications Related DocumentationPage Index Sonet