Emerson PMC-CGM manual Perform Firmware/Software Upgrade, Upgrading the firmware/software

Page 42

Access and Configuration	Perform Firmware/Software Upgrade

7.For the T4 path, repeat steps 5 and 6 with the cgmT4InputPriority object OID:.1.3.6.1.4.1.3656.8152.1.1.1.1.5.<instance number which is equal to input number -1>.

8.Go to cgmInputRefASource object OID:.1.3.6.1.4.1.3656.8152.1.4.16.0.

9.Select the source (chassis) of the primary linecard derived reference clock. The following values are possible:

local reference A (0) - default value local reference B (1)

Chassis 2 reference A (2) Chassis 2 reference B (3) Chassis 3 reference A (4) Chassis 3 reference B (5)

10.Go to cgmInputRefBSource object OID:.1.3.6.1.4.1.3656.8152.1.4.18.0.

11.Select the source of the "secondary" linecard derived reference clock (REFB input to PLL). Not relevant for distributed mode.

local reference A (0)

local reference B (1) - default value Chassis 2 reference A (2)

Chassis 2 reference B (3) Chassis 3 reference A (4) Chassis 3 reference B (5)

4.4.8Perform Firmware/Software Upgrade

You can upgrade the firmware/software of the PMC-CGM via the MIB. The firmware/software upgrade is done by downloading an image from a TFTP server and programming it into the inactive partition of the boot flash (that means not the one which is currently running) which is split into two partitions of 32MB each. By default, only one of the two partitions (the active partition) is accessible.

Upgrading the firmware/software

To upgrade the firmware/software, proceed as follows:

1.Start SNMP manager or MIB browser.

2.Connect to the PMC-CGM using one of its IP addresses.

3.Go to object cgmFwUpdateHost OID: .1.3.6.1.4.1.3656.8152.1.3.26.0.

4.Enter the IP address of the TFTP server that contains the new image.

5.Go to object cgmFwUpdateFile OID:.1.3.6.1.4.1.3656.8152.1.3.27.0.

6.Enter the file that contains the new image.

7.Go to object cgmFwUpdateMd5 OID:.1.3.6.1.4.1.3656.8152.1.3.28.0.

42	PMC-CGM Installation and Use (6806800D53C)

Image 42

Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C Overview of Contents About this ManualAbbreviations About this Manual Abbreviation Definition RTMConventions Notation DescriptionBold About this Manual Notation Description Summary of ChangesComments and Suggestions Part Number Publication Date DescriptionSafety Notes Electrical InterferenceInstallation Safety NotesOperation Configuration Switches Cabling and ConnectorsEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Schaltereinstellungen Kabel und SteckerUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionIntroduction Standard Compliances Standard CompliancesStandard Compliances and Clocking Standards Standard DescriptionOrdering InformationIntroduction Ordering InformationAvailable Board Variants Order Number DescriptionPage Overview Hardware Preparation and InstallationBefore Installation Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsFeature Operating Non-Operating packed state DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature ValueConfiguring the Module Switch LocationInstalling and Removing the Module Switch SettingsSwitch Hardware Upgrades and Acessories Installation ProcedureRemoval Procedure Controls, LEDs and Connectors Front Panel Connectors and LEDsLayout Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMAccess Access and Configuration CablingCabling MIB Browser Settings Using a MIB BrowserConfiguring the PMC-CGM Using a MIB Browser Access and ConfigurationDefining the IP address of the protection partner module Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining Snmp Trap DestinationsConfiguring the interface mode Configure the Interface ModeConfigure the Bits Interface Configuring the Bits interfaceConfiguring the initial master/slave roles Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Setting up a multi-shelf configurationConfigure the Reference Clock Configuring the reference clock source for the T0/T4 pathConfigure the Reference Clock Access and Configuration Perform Firmware/Software Upgrade Upgrading the firmware/softwareReset the PMC-CGM Resetting the PMC-CGM via SnmpReset the PMC-CGM Access and Configuration Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Structure MIB DescriptionCgmControl CgmInputTableMIB DescriptioncgmControl DefaultInput Assignments Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys MIB Description CgmSysCgmEventTable Not supported on PMC-CGMEvent Codes and Severity MIB DescriptioncgmSysCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistCgmClkDist Objects CgmClkDist MIB DescriptionNot applicable for PMC-CGM PLL Related Documentation Emerson Network Power Embedded Computing DocumentsRelated Specifications Document Title Publication NumberPage Index Sonet