Emerson manual CgmEventTable, CgmSys MIB Description, Not supported on PMC-CGM

Page 55

cgmSys

MIB Description

 

 

Table 5-5 cgmControl Elements (continued)

OID

MIB Object

Description

Access

 

 

 

 

.1.1.41

cgmCLK2OutputFrequency

The output frequency of CLK2:

r/w

 

 

0

- CLK2 output disabled

 

 

 

1

- 19.44 MHz

 

 

 

Default value is (1).

 

 

 

 

 

.1.1.42

cgmCLK3OutputFrequency

Not supported on PMC-CGM

r/w

 

 

 

 

.1.1.43

cgmCLK1OutputFramePulse

The output frame pulse of the T1 clock:

r/w

 

 

0

- Not inverted, not pulsed

 

 

 

1

- Not inverted, pulsed

 

 

 

2

- Inverted, not pulsed

 

 

 

3

- Inverted, pulsed

 

 

 

Default value is (0).

 

 

 

 

 

.1.1.44

cgmT4ClkSquelch

When set to 0 (enable) the output of the T4 PLL

 

 

 

is squelched if no valid input is selected.

 

 

 

If set to 1 (disable) an output is provided in any

 

 

 

case.

 

 

 

 

 

 

5.3cgmSys

The cgmSys branch contains the following information:

zcgmEventTable - for details refer to Table 5-6 on page 55.

zVarious MIB objects that are described in Table 5-8 on page 58.

For a description on how to use these objects refer to Configure Parameters for Event Handling on page 44, Perform Firmware/Software Upgrade on page 42.

The cgmEventTable (OID:.1.3.6.1.4.1.3656.8152.1.3.1) uses cgmEventNumber as index. The elements of the trap definiton cgmLogEvent (OID:.1.3.6.1.4.1.3656.8152.1.2.0.1) is identical to the elements defined in cgmEventTable.

Table 5-6 cgmEventTable

 

OID

MIB Object

Description

Access

 

 

 

 

 

 

.1.3.1.1.2

cgmEventTime

System time stamp when event occurred (this is the

r

 

 

 

module's run-time since power-up).

 

 

 

 

 

 

 

.1.3.1.1.3

cgmEventSeverity

The event's severity level

r

 

 

 

1.

Critical (0): An error has occurred which needs

 

 

 

 

immediate attention.

 

 

 

 

2.

Warnings (1): An error has occurred which may affect

 

 

 

 

board operation but does not require immediate attention.

 

 

 

 

3.

Events (2): An event occurred in a board subsystem

 

 

 

 

which may need attention (e.g. the PLL gained lock).

 

 

 

 

4.

Information (3): Various information messages helpful

 

 

 

 

for troubleshooting or monitoring the state of the CGM

 

 

 

 

module.

 

 

 

 

 

 

 

 

 

 

 

 

 

PMC-CGM Installation and Use (6806800D53C)

 

55

Image 55
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C About this Manual Overview of ContentsAbbreviations RTM About this Manual Abbreviation DefinitionNotation Description ConventionsBold Part Number Publication Date Description Summary of ChangesComments and Suggestions About this Manual Notation DescriptionElectrical Interference Safety NotesSafety Notes InstallationOperation Cabling and Connectors Configuration SwitchesEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Kabel und Stecker SchaltereinstellungenUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Description Standard CompliancesStandard Compliances and Clocking Standards Introduction Standard CompliancesOrder Number Description Ordering InformationAvailable Board Variants Ordering InformationIntroductionPage Unpacking and Inspecting the Module Hardware Preparation and InstallationBefore Installation OverviewRequirements Hardware Preparation and Installation RequirementsFeature Value DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature Operating Non-Operating packed stateSwitch Location Configuring the ModuleSwitch Settings Installing and Removing the ModuleSwitch Installation Procedure Hardware Upgrades and AcessoriesRemoval Procedure Front Panel Connectors and LEDs Controls, LEDs and ConnectorsLayout Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationAccess and Configuration Cabling AccessCabling Using a MIB Browser Access and Configuration Using a MIB BrowserConfiguring the PMC-CGM MIB Browser SettingsDefining Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining the IP address of the protection partner moduleConfiguring the Bits interface Configure the Interface ModeConfigure the Bits Interface Configuring the interface modeSetting up a multi-shelf configuration Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Configuring the initial master/slave rolesConfiguring the reference clock source for the T0/T4 path Configure the Reference ClockConfigure the Reference Clock Access and Configuration Upgrading the firmware/software Perform Firmware/Software UpgradeResetting the PMC-CGM via Snmp Reset the PMC-CGMReset the PMC-CGM Access and Configuration Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmInputTable MIB DescriptionCgmControl MIB StructureInstance CgmInputNumber CgmInputName CgmInputFrequency DefaultInput Assignments MIB DescriptioncgmControlCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl Not supported on PMC-CGM CgmSysCgmEventTable CgmSys MIB DescriptionMIB DescriptioncgmSys Event Codes and SeverityCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistCgmClkDist MIB Description CgmClkDist ObjectsNot applicable for PMC-CGM PLL Document Title Publication Number Emerson Network Power Embedded Computing DocumentsRelated Specifications Related DocumentationPage Index Sonet