Emerson PMC-CGM manual LED Description, Name Description

Page 34

Controls, LEDs and Connectors	LEDs

You can find a description of the LEDs in the following table.

Table 3-1 LED Description

Name	Description

B1	BITS Interface 1 Status
	Green: BITS interface 1 is in use and status is okay
	Orange: BITS interface 1 is in use and status is not okay
	Red: : BITS interface 1 is out-of-service
	OFF: Not defined

B2	BITS Interface 2 Status
	Green: BITS interface 2 is in use and status is okay
	Orange: BITS interface 2 is in use and status is not okay
	Red: : BITS interface 2 is out-of-service
	OFF: Not defined

M/S	Master/Slave Operation
	Green: PMC-CGM operates as Master
	Amber: Not defined
	Yellow: PMC-CGM operates as Slave
	OFF: PMC-CGM is non-operational (by application)

Mode	Mode
	Green: PMC-CGM operates in locked mode
	Amber: PMC-CGM operates in holdover mode
	Yellow: PMC-CGM operates in free-run mode
	OFF: not defined

OOS	Out-Of-Service
	Red: PMC-CGM is out-of-service
	Off: Not defined

IS	In Service
	Green: PMC-CGM is in service
	Off: Not defined

34	PMC-CGM Installation and Use (6806800D53C)

Image 34

Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C About this Manual Overview of ContentsAbbreviations About this Manual Abbreviation Definition RTMNotation Description ConventionsBold About this Manual Notation Description Summary of ChangesComments and Suggestions Part Number Publication Date DescriptionSafety Notes Electrical InterferenceSafety Notes InstallationOperation Cabling and Connectors Configuration SwitchesEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Kabel und Stecker SchaltereinstellungenUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionIntroduction Standard Compliances Standard CompliancesStandard Compliances and Clocking Standards Standard DescriptionOrdering InformationIntroduction Ordering InformationAvailable Board Variants Order Number DescriptionPage Overview Hardware Preparation and InstallationBefore Installation Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsFeature Operating Non-Operating packed state DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature ValueConfiguring the Module Switch LocationSwitch Settings Installing and Removing the ModuleSwitch Installation Procedure Hardware Upgrades and AcessoriesRemoval Procedure Front Panel Connectors and LEDs Controls, LEDs and ConnectorsLayout Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMAccess and Configuration Cabling AccessCabling MIB Browser Settings Using a MIB BrowserConfiguring the PMC-CGM Using a MIB Browser Access and ConfigurationDefining the IP address of the protection partner module Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining Snmp Trap DestinationsConfiguring the interface mode Configure the Interface ModeConfigure the Bits Interface Configuring the Bits interfaceConfiguring the initial master/slave roles Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Setting up a multi-shelf configurationConfiguring the reference clock source for the T0/T4 path Configure the Reference ClockConfigure the Reference Clock Access and Configuration Perform Firmware/Software Upgrade Upgrading the firmware/softwareResetting the PMC-CGM via Snmp Reset the PMC-CGMReset the PMC-CGM Access and Configuration Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Structure MIB DescriptionCgmControl CgmInputTableMIB DescriptioncgmControl DefaultInput Assignments Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys MIB Description CgmSysCgmEventTable Not supported on PMC-CGMMIB DescriptioncgmSys Event Codes and SeverityCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistCgmClkDist MIB Description CgmClkDist ObjectsNot applicable for PMC-CGM PLL Related Documentation Emerson Network Power Embedded Computing DocumentsRelated Specifications Document Title Publication NumberPage Index Sonet