Emerson
manual
List of Figures PMC-CGM Installation and Use 6806800D53C
Specifications
Install
Default
Configuration Switches
Reset the PMC-CGM
Accessing the PMC-CGM
Controls, LEDs and Connectors
Removal Procedure
Switch Settings
Safety
Page 8
List of Figures
8
PMC-CGM
Installation and Use (6806800D53C)
Page 7
Page 9
Image 8
Page 7
Page 9
Contents
PMC-CGM
Contact Address
Contents
Contents
List of Tables
List of Tables PMC-CGM Installation and Use 6806800D53C
List of Figures
Location of PMC Slot on ATCA-F103
List of Figures PMC-CGM Installation and Use 6806800D53C
Abbreviations
Overview of Contents
About this Manual
About this Manual Abbreviation Definition
RTM
Bold
Conventions
Notation Description
Summary of Changes
Comments and Suggestions
About this Manual Notation Description
Part Number Publication Date Description
Safety Notes
Electrical Interference
Operation
Installation
Safety Notes
Environment
Configuration Switches
Cabling and Connectors
Safety Notes PMC-CGM Installation and Use 6806800D53C
Sicherheitshinweise
EMV
Sicherheitshinweise
Umweltschutz
Schaltereinstellungen
Kabel und Stecker
Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C
Features
Introduction
Standard Compliances
Standard Compliances and Clocking Standards
Introduction Standard Compliances
Standard Description
Ordering Information
Available Board Variants
Ordering InformationIntroduction
Order Number Description
Page
Hardware Preparation and Installation
Before Installation
Overview
Unpacking and Inspecting the Module
Hardware Preparation and Installation Requirements
Requirements
DC Module Power Requirements
RequirementsHardware Preparation and Installation
Feature Operating Non-Operating packed state
Feature Value
Configuring the Module
Switch Location
Switch
Installing and Removing the Module
Switch Settings
Removal Procedure
Hardware Upgrades and Acessories
Installation Procedure
Layout
Controls, LEDs and Connectors
Front Panel Connectors and LEDs
Bits Interface Connectors
Controls, LEDs and Connectors Bits Interface Connectors
LEDs Controls, LEDs and Connectors
LEDs
LED Description
Name Description
Access and Configuration
Accessing the PMC-CGM
Cabling
Access
Access and Configuration Cabling
Using a MIB Browser
Configuring the PMC-CGM
MIB Browser Settings
Using a MIB Browser Access and Configuration
Define IP Address of the Protection Partner Module
Define Snmp Trap Destinations
Defining the IP address of the protection partner module
Defining Snmp Trap Destinations
Configure the Interface Mode
Configure the Bits Interface
Configuring the interface mode
Configuring the Bits interface
Configure Initial Master/Slave Role
Setup Multi-Shelf Configuration
Configuring the initial master/slave roles
Setting up a multi-shelf configuration
Configure the Reference Clock Access and Configuration
Configure the Reference Clock
Configuring the reference clock source for the T0/T4 path
Perform Firmware/Software Upgrade
Upgrading the firmware/software
Reset the PMC-CGM Access and Configuration
Reset the PMC-CGM
Resetting the PMC-CGM via Snmp
Configure Parameters for Event Handling
Configuring event handling parameters
PMC-CGM Installation and Use 6806800D53C
Page
MIB Description
CgmControl
MIB Structure
CgmInputTable
Default
Input Assignments
MIB DescriptioncgmControl
Instance CgmInputNumber CgmInputName CgmInputFrequency
CgmBitsTable
CgmControl MIB Description
Not yet supported
CgmControlMIB Description
Is present. This should only be set for test purposes
Input When in nonrevertive operation 1, a selected
CgmControl Elements
MIB Description CgmControl
CgmSys
CgmEventTable
CgmSys MIB Description
Not supported on PMC-CGM
Code Severity Description
Event Codes and Severity
MIB DescriptioncgmSys
CgmSysMIB Description
CgmSys Objects
New firmware image
CgmClkDist
MIB Description CgmClkDist
Not applicable for PMC-CGM
CgmClkDist Objects
CgmClkDist MIB Description
PLL
Emerson Network Power Embedded Computing Documents
Related Specifications
Related Documentation
Document Title Publication Number
Page
Index
Sonet
Related pages
All Install page
Can I adjust the belt tension according to the
Exmark maintenance schedule
?
Top
Page
Image
Contents