Emerson PMC-CGM manual Related Documentation, Emerson Network Power Embedded Computing Documents

Page 63

Related Documentation

A

A.1 Emerson Network Power - Embedded Computing Documents

The Emerson Network Power - Embedded Computing publications listed below are referenced in this manual. You can obtain electronic copies of Emerson Network Power - Embedded Computing publications by contacting your local Emerson sales office. For documentation of final released (GA) products, you can also visit the following website: http://www.emersonnetworkpowerembeddedcomputing.com > Resource Center > Technical Documentation Search. This site provides the most up-to-date copies of Emerson Network Power - Embedded Computing product documentation.

Table A-1 Emerson Network Power - Embedded Computing Publications

Document Title	Publication Number

Centellis CO 31kX Installation and Use	6806800A99

ATCA-F103 Installation and Use	6806800D97

ARTM-F103-STX Installation and Use	6806800D79

PMC-CGM: Control via IPMI Programmer’s Reference	6806800D54

CABLE-CGM2-CLK Installation and Use	6806800F47

A.2 Related Specifications

For additional information, refer to the following table for related specifications. As an additional help, a source for the listed document is provided. Please note that, while these sources have been verified, the information is subject to change without notice.

Company/Org.	Documents

PICMG	PICMG 3.0 AdvancedTCA Base Specification
can be ordered via www.picmg.org

PMC-CGM Installation and Use (6806800D53C)

63

Image 63

Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C Overview of Contents About this ManualAbbreviations RTM About this Manual Abbreviation DefinitionConventions Notation DescriptionBold Part Number Publication Date Description Summary of ChangesComments and Suggestions About this Manual Notation DescriptionElectrical Interference Safety NotesInstallation Safety NotesOperation Configuration Switches Cabling and ConnectorsEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Schaltereinstellungen Kabel und SteckerUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Description Standard CompliancesStandard Compliances and Clocking Standards Introduction Standard CompliancesOrder Number Description Ordering InformationAvailable Board Variants Ordering InformationIntroductionPage Unpacking and Inspecting the Module Hardware Preparation and InstallationBefore Installation OverviewRequirements Hardware Preparation and Installation RequirementsFeature Value DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature Operating Non-Operating packed stateSwitch Location Configuring the ModuleInstalling and Removing the Module Switch SettingsSwitch Hardware Upgrades and Acessories Installation ProcedureRemoval Procedure Controls, LEDs and Connectors Front Panel Connectors and LEDsLayout Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationAccess Access and Configuration CablingCabling Using a MIB Browser Access and Configuration Using a MIB BrowserConfiguring the PMC-CGM MIB Browser SettingsDefining Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining the IP address of the protection partner moduleConfiguring the Bits interface Configure the Interface ModeConfigure the Bits Interface Configuring the interface modeSetting up a multi-shelf configuration Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Configuring the initial master/slave rolesConfigure the Reference Clock Configuring the reference clock source for the T0/T4 pathConfigure the Reference Clock Access and Configuration Upgrading the firmware/software Perform Firmware/Software UpgradeReset the PMC-CGM Resetting the PMC-CGM via SnmpReset the PMC-CGM Access and Configuration Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmInputTable MIB DescriptionCgmControl MIB StructureInstance CgmInputNumber CgmInputName CgmInputFrequency DefaultInput Assignments MIB DescriptioncgmControlCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl Not supported on PMC-CGM CgmSysCgmEventTable CgmSys MIB DescriptionEvent Codes and Severity MIB DescriptioncgmSysCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistCgmClkDist Objects CgmClkDist MIB DescriptionNot applicable for PMC-CGM PLL Document Title Publication Number Emerson Network Power Embedded Computing DocumentsRelated Specifications Related DocumentationPage Index Sonet