Emerson PMC-CGM manual Configuring the Module, Switch Location

Page 28

Hardware Preparation and Installation	Configuring the Module

2.3Configuring the Module

The module provides the configuration switch SW1 as shown in the following figure. The switch settings shown in the figure correspond to the default settings. The switches are displayed as the small white squares.

Figure 2-1 Switch Location

Product Malfunction

Switches marked as 'reserved' might carry production-related functions and can cause the product to malfunction if their setting is changed.

Therefore, do not change settings of switches marked as 'reserved'. The setting of switches which are not marked as 'reserved' has to be checked and changed before product installation.

Product Damage

Setting/resetting the switches during operation can cause product damage. Therefore, check and change switch settings before you install the product.

28	PMC-CGM Installation and Use (6806800D53C)

Image 28

Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C About this Manual Overview of ContentsAbbreviations About this Manual Abbreviation Definition RTMNotation Description ConventionsBold Summary of Changes Comments and SuggestionsAbout this Manual Notation Description Part Number Publication Date DescriptionSafety Notes Electrical InterferenceSafety Notes InstallationOperation Cabling and Connectors Configuration SwitchesEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Kabel und Stecker SchaltereinstellungenUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionStandard Compliances Standard Compliances and Clocking StandardsIntroduction Standard Compliances Standard DescriptionOrdering Information Available Board VariantsOrdering InformationIntroduction Order Number DescriptionPage Hardware Preparation and Installation Before InstallationOverview Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsDC Module Power Requirements RequirementsHardware Preparation and InstallationFeature Operating Non-Operating packed state Feature ValueConfiguring the Module Switch LocationSwitch Settings Installing and Removing the ModuleSwitch Installation Procedure Hardware Upgrades and AcessoriesRemoval Procedure Front Panel Connectors and LEDs Controls, LEDs and ConnectorsLayout Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMAccess and Configuration Cabling AccessCabling Using a MIB Browser Configuring the PMC-CGMMIB Browser Settings Using a MIB Browser Access and ConfigurationDefine IP Address of the Protection Partner Module Define Snmp Trap DestinationsDefining the IP address of the protection partner module Defining Snmp Trap DestinationsConfigure the Interface Mode Configure the Bits InterfaceConfiguring the interface mode Configuring the Bits interfaceConfigure Initial Master/Slave Role Setup Multi-Shelf ConfigurationConfiguring the initial master/slave roles Setting up a multi-shelf configurationConfiguring the reference clock source for the T0/T4 path Configure the Reference ClockConfigure the Reference Clock Access and Configuration Perform Firmware/Software Upgrade Upgrading the firmware/softwareResetting the PMC-CGM via Snmp Reset the PMC-CGMReset the PMC-CGM Access and Configuration Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Description CgmControlMIB Structure CgmInputTableDefault Input AssignmentsMIB DescriptioncgmControl Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys CgmEventTableCgmSys MIB Description Not supported on PMC-CGMMIB DescriptioncgmSys Event Codes and SeverityCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistCgmClkDist MIB Description CgmClkDist ObjectsNot applicable for PMC-CGM PLL Emerson Network Power Embedded Computing Documents Related SpecificationsRelated Documentation Document Title Publication NumberPage Index Sonet