Emerson PMC-CGM manual Bits Interface Connectors

Page 32

Controls, LEDs and Connectors

BITS Interface Connectors

 

 

The Ethernet ports for the PMC-CGM are located on the ARTM-F103.

Figure 3-2 Front Panel

3.3.1BITS Interface Connectors

The module provides two RJ-45 BITS front panel connectors.

Product Damage

The RJ-45 connector(s) on the face plate are BITS interfaces. Connecting a telephone to such a connector may destroy your telephone as well as the product.

Make sure that BITS connectors near your working area are clearly marked as network connectors. In addition, observe the following safety notes:

zVerify that the length of an electric cable connected to a BITS bushing does not exceed 100 m.

zMake sure the BITS bushing of the system is connected only to

Telecommunication Network Voltage level 1 (TNV-1) circuits.

If in doubt, ask your system administrator.

32

PMC-CGM Installation and Use (6806800D53C)

Image 32
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C Abbreviations Overview of ContentsAbout this Manual About this Manual Abbreviation Definition RTMBold ConventionsNotation Description Summary of Changes Comments and SuggestionsAbout this Manual Notation Description Part Number Publication Date DescriptionSafety Notes Electrical InterferenceOperation InstallationSafety Notes Environment Configuration SwitchesCabling and Connectors Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Umweltschutz SchaltereinstellungenKabel und Stecker Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionStandard Compliances Standard Compliances and Clocking StandardsIntroduction Standard Compliances Standard DescriptionOrdering Information Available Board VariantsOrdering InformationIntroduction Order Number DescriptionPage Hardware Preparation and Installation Before InstallationOverview Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsDC Module Power Requirements RequirementsHardware Preparation and InstallationFeature Operating Non-Operating packed state Feature ValueConfiguring the Module Switch LocationSwitch Installing and Removing the ModuleSwitch Settings Removal Procedure Hardware Upgrades and AcessoriesInstallation Procedure Layout Controls, LEDs and ConnectorsFront Panel Connectors and LEDs Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMCabling AccessAccess and Configuration Cabling Using a MIB Browser Configuring the PMC-CGMMIB Browser Settings Using a MIB Browser Access and ConfigurationDefine IP Address of the Protection Partner Module Define Snmp Trap DestinationsDefining the IP address of the protection partner module Defining Snmp Trap DestinationsConfigure the Interface Mode Configure the Bits InterfaceConfiguring the interface mode Configuring the Bits interfaceConfigure Initial Master/Slave Role Setup Multi-Shelf ConfigurationConfiguring the initial master/slave roles Setting up a multi-shelf configurationConfigure the Reference Clock Access and Configuration Configure the Reference ClockConfiguring the reference clock source for the T0/T4 path Perform Firmware/Software Upgrade Upgrading the firmware/softwareReset the PMC-CGM Access and Configuration Reset the PMC-CGMResetting the PMC-CGM via Snmp Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Description CgmControlMIB Structure CgmInputTableDefault Input AssignmentsMIB DescriptioncgmControl Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys CgmEventTableCgmSys MIB Description Not supported on PMC-CGMCode Severity Description Event Codes and SeverityMIB DescriptioncgmSys CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistNot applicable for PMC-CGM CgmClkDist ObjectsCgmClkDist MIB Description PLL Emerson Network Power Embedded Computing Documents Related SpecificationsRelated Documentation Document Title Publication NumberPage Index Sonet