Emerson PMC-CGM manual Hardware Preparation and Installation Requirements

Page 26

Hardware Preparation and Installation

Requirements

 

 

2.Check for damage and report any damage or differences to the customer service.

3.Remove the desiccant bag shipped together with the module and dispose of it according to your country’s legislation.

The product is thoroughly inspected before shipment. If any damage occurred during transportation or any items are missing, please contact our customer's service immediately.

2.2.2Requirements

Before you power up the module, calculate the power needed according to your system configuration.

2.2.2.1Environmental Requirements

You must make sure that the board, when operated in your particular system configuration, meets the environmental requirements specified below.

Operating temperatures refer to the temperature of the air circulating around the board and not to the component temperature.

Board Damage

High humidity and condensation on the board surface causes short circuits.

Do not operate the board outside the specified environmental limits. Make sure the board is completely dry and there is no moisture on any surface before applying power.

26

PMC-CGM Installation and Use (6806800D53C)

Image 26
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C Abbreviations Overview of ContentsAbout this Manual About this Manual Abbreviation Definition RTMBold ConventionsNotation Description About this Manual Notation Description Summary of ChangesComments and Suggestions Part Number Publication Date DescriptionSafety Notes Electrical InterferenceOperation InstallationSafety Notes Environment Configuration SwitchesCabling and Connectors Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Umweltschutz SchaltereinstellungenKabel und Stecker Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionIntroduction Standard Compliances Standard CompliancesStandard Compliances and Clocking Standards Standard DescriptionOrdering InformationIntroduction Ordering InformationAvailable Board Variants Order Number DescriptionPage Overview Hardware Preparation and InstallationBefore Installation Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsFeature Operating Non-Operating packed state DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature ValueConfiguring the Module Switch LocationSwitch Installing and Removing the ModuleSwitch Settings Removal Procedure Hardware Upgrades and AcessoriesInstallation Procedure Layout Controls, LEDs and ConnectorsFront Panel Connectors and LEDs Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMCabling AccessAccess and Configuration Cabling MIB Browser Settings Using a MIB BrowserConfiguring the PMC-CGM Using a MIB Browser Access and ConfigurationDefining the IP address of the protection partner module Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining Snmp Trap DestinationsConfiguring the interface mode Configure the Interface ModeConfigure the Bits Interface Configuring the Bits interfaceConfiguring the initial master/slave roles Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Setting up a multi-shelf configurationConfigure the Reference Clock Access and Configuration Configure the Reference ClockConfiguring the reference clock source for the T0/T4 path Perform Firmware/Software Upgrade Upgrading the firmware/softwareReset the PMC-CGM Access and Configuration Reset the PMC-CGMResetting the PMC-CGM via Snmp Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Structure MIB DescriptionCgmControl CgmInputTableMIB DescriptioncgmControl DefaultInput Assignments Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys MIB Description CgmSysCgmEventTable Not supported on PMC-CGMCode Severity Description Event Codes and SeverityMIB DescriptioncgmSys CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistNot applicable for PMC-CGM CgmClkDist ObjectsCgmClkDist MIB Description PLL Related Documentation Emerson Network Power Embedded Computing DocumentsRelated Specifications Document Title Publication NumberPage Index Sonet