Emerson PMC-CGM manual Safety Notes, Electrical Interference

Page 13

Safety Notes

This section provides warnings that precede potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed during all phases of operation, service, and repair of this equipment. You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment. Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment.

Emerson intends to provide all necessary information to install and handle the product in this manual. Because of the complexity of this product and its various uses, we do not guarantee that the given information is complete. If you need additional information, ask your Emerson representative.

The product has been designed to meet the standard industrial safety requirements. It must not be used except in its specific area of office telecommunication industry and industrial control.

Only personnel trained by Emerson or persons qualified in electronics or electrical engineering are authorized to install, remove or maintain the product.

The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel.

Keep away from live circuits inside the equipment. Operating personnel must not remove equipment covers. Only factory authorized service personnel or other qualified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment.

Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided. Contact your local Emerson representative for service and repair to make sure that all safety features are maintained.

Electrical Interference

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

PMC-CGM Installation and Use (6806800D53C)

13

Image 13
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C About this Manual Overview of ContentsAbbreviations RTM About this Manual Abbreviation DefinitionNotation Description ConventionsBold Comments and Suggestions Summary of ChangesAbout this Manual Notation Description Part Number Publication Date DescriptionElectrical Interference Safety NotesSafety Notes InstallationOperation Cabling and Connectors Configuration SwitchesEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Kabel und Stecker SchaltereinstellungenUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Compliances and Clocking Standards Standard CompliancesIntroduction Standard Compliances Standard DescriptionAvailable Board Variants Ordering InformationOrdering InformationIntroduction Order Number DescriptionPage Before Installation Hardware Preparation and InstallationOverview Unpacking and Inspecting the ModuleRequirements Hardware Preparation and Installation RequirementsRequirementsHardware Preparation and Installation DC Module Power RequirementsFeature Operating Non-Operating packed state Feature ValueSwitch Location Configuring the ModuleSwitch Settings Installing and Removing the ModuleSwitch Installation Procedure Hardware Upgrades and AcessoriesRemoval Procedure Front Panel Connectors and LEDs Controls, LEDs and ConnectorsLayout Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationAccess and Configuration Cabling AccessCabling Configuring the PMC-CGM Using a MIB BrowserMIB Browser Settings Using a MIB Browser Access and ConfigurationDefine Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefining the IP address of the protection partner module Defining Snmp Trap DestinationsConfigure the Bits Interface Configure the Interface ModeConfiguring the interface mode Configuring the Bits interfaceSetup Multi-Shelf Configuration Configure Initial Master/Slave RoleConfiguring the initial master/slave roles Setting up a multi-shelf configurationConfiguring the reference clock source for the T0/T4 path Configure the Reference ClockConfigure the Reference Clock Access and Configuration Upgrading the firmware/software Perform Firmware/Software UpgradeResetting the PMC-CGM via Snmp Reset the PMC-CGMReset the PMC-CGM Access and Configuration Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmControl MIB DescriptionMIB Structure CgmInputTableInput Assignments DefaultMIB DescriptioncgmControl Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl CgmEventTable CgmSysCgmSys MIB Description Not supported on PMC-CGMMIB DescriptioncgmSys Event Codes and SeverityCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistCgmClkDist MIB Description CgmClkDist ObjectsNot applicable for PMC-CGM PLL Related Specifications Emerson Network Power Embedded Computing DocumentsRelated Documentation Document Title Publication NumberPage Index Sonet