Emerson PMC-CGM manual Installing and Removing the Module, Switch Settings

Page 29

Installing and Removing the Module

Hardware Preparation and Installation

 

 

Table 2-3 Switch Settings

Switch

SW1-1

SW1-2

SW1-3

SW1-4

Description

Reserved (OFF: default value)

Reserved (OFF: default value)

Restores default static IP addresses

OFF: Dynamic IP addresses are assigned by the ATCA-M100, for details refer to Table "MIB Browser Settings" on page 37 (default)

ON: Static IP addresses are assigned

192.168.21.40: acces via ETHA on ARTM-F103-STX

192.168.22.40: acces via ETHB on ARTM-F103-STX

Reserved (OFF: default value)

2.4Installing and Removing the Module

The PMC-CGM can be installed on the PMC slot of the AdvancedTCA ATCA-F103 blade.

Figure 2-2 Location of PMC Slot on ATCA-F103

PMC-CGM Installation and Use (6806800D53C)

29

Image 29
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C Abbreviations Overview of ContentsAbout this Manual RTM About this Manual Abbreviation DefinitionBold ConventionsNotation Description Comments and Suggestions Summary of ChangesAbout this Manual Notation Description Part Number Publication Date DescriptionElectrical Interference Safety NotesOperation InstallationSafety Notes Environment Configuration SwitchesCabling and Connectors Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Umweltschutz SchaltereinstellungenKabel und Stecker Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Compliances and Clocking Standards Standard CompliancesIntroduction Standard Compliances Standard DescriptionAvailable Board Variants Ordering InformationOrdering InformationIntroduction Order Number DescriptionPage Before Installation Hardware Preparation and InstallationOverview Unpacking and Inspecting the ModuleRequirements Hardware Preparation and Installation RequirementsRequirementsHardware Preparation and Installation DC Module Power RequirementsFeature Operating Non-Operating packed state Feature ValueSwitch Location Configuring the ModuleSwitch Installing and Removing the ModuleSwitch Settings Removal Procedure Hardware Upgrades and AcessoriesInstallation Procedure Layout Controls, LEDs and ConnectorsFront Panel Connectors and LEDs Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationCabling AccessAccess and Configuration Cabling Configuring the PMC-CGM Using a MIB BrowserMIB Browser Settings Using a MIB Browser Access and ConfigurationDefine Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefining the IP address of the protection partner module Defining Snmp Trap DestinationsConfigure the Bits Interface Configure the Interface ModeConfiguring the interface mode Configuring the Bits interfaceSetup Multi-Shelf Configuration Configure Initial Master/Slave RoleConfiguring the initial master/slave roles Setting up a multi-shelf configurationConfigure the Reference Clock Access and Configuration Configure the Reference ClockConfiguring the reference clock source for the T0/T4 path Upgrading the firmware/software Perform Firmware/Software UpgradeReset the PMC-CGM Access and Configuration Reset the PMC-CGMResetting the PMC-CGM via Snmp Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmControl MIB DescriptionMIB Structure CgmInputTableInput Assignments DefaultMIB DescriptioncgmControl Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl CgmEventTable CgmSysCgmSys MIB Description Not supported on PMC-CGMCode Severity Description Event Codes and SeverityMIB DescriptioncgmSys CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistNot applicable for PMC-CGM CgmClkDist ObjectsCgmClkDist MIB Description PLL Related Specifications Emerson Network Power Embedded Computing DocumentsRelated Documentation Document Title Publication NumberPage Index Sonet