Emerson PMC-CGM manual MIB Description CgmControl

Page 54

MIB Description

cgmControl

 

 

Table 5-5 cgmControl Elements (continued)

OID

MIB Object

Description

Access

 

 

 

 

.1.1.19

cgmProtectionState

Indicates whether this module is the master or

r

 

 

slave of a protection pair:

 

 

 

0

- standaloneMaster: Communication with the

 

 

 

partner is not possible and the module is running

 

 

 

in master mode.

 

 

 

1

- slave

 

 

 

2

- master

 

 

 

 

 

.1.1.20

cgmProtectionCmd

Can be used to manually change the state of the

r/w

 

 

module.

 

 

 

0

- Attempt to become master. This is only

 

 

 

possible if a valid clock input is present.

 

 

 

1

- Give up mastership to the protection partner.

 

 

 

This is only possible if the partner (slave) has a

 

 

 

valid input other than MS_SYNC.

 

 

 

Whether the operation failed or succeeded can

 

 

 

be seen in the cgmProtectionState element.

 

 

 

 

 

.1.1.21

cgmProtectionMasterToSlave

The tracking delay for the master/slave

r/w

 

TrackDelay

synchronization signal in ns units.

 

 

 

Default value is automatically configured.

 

 

 

 

 

.1.1.22

cgmProtectionPartnerAddress

The IP address of the protection partner.

r/w

 

 

Default value depends on your configuration.

 

 

 

 

 

.1.1.30

cgmPathStateT0

The current state of the T0 PLL:

r

 

 

0

- freerun

 

 

 

1

- locked

 

 

 

2

- holdover

 

 

 

3

- preLocked

 

 

 

4

- preLocked2

 

 

 

5

- phaseLost

 

 

 

6

- forcedFreerun

 

 

 

7

- forcedHoldover

 

 

 

 

 

.1.1.32

cgmPathInputT0

The input currently selected for the T0 PLL. The

r

 

 

value 255 indicates that no input is selected.

 

 

 

 

 

.1.1.34

cgmPathInputT4

The input currently selected for the T4 PLL. The

r

 

 

value 255 indicates that no input is selected.

 

 

 

Other values reflect the cgmInputNumber

 

 

 

element in the cgmInputTable table, for details

 

 

 

refer to Table "Input Assignments" on page 48.

 

 

 

 

 

.1.1.40

cgmCLK1OutputFrequency

The output frequency of CLK1:

r/w

 

 

0

- CLK1 output disabled

 

 

 

1

- 8 KHz

 

 

 

Default value is (1).

 

 

 

 

 

 

54

PMC-CGM Installation and Use (6806800D53C)

Image 54
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C Overview of Contents About this ManualAbbreviations About this Manual Abbreviation Definition RTMConventions Notation DescriptionBold About this Manual Notation Description Summary of ChangesComments and Suggestions Part Number Publication Date DescriptionSafety Notes Electrical InterferenceInstallation Safety NotesOperation Configuration Switches Cabling and ConnectorsEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Schaltereinstellungen Kabel und SteckerUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionIntroduction Standard Compliances Standard CompliancesStandard Compliances and Clocking Standards Standard DescriptionOrdering InformationIntroduction Ordering InformationAvailable Board Variants Order Number DescriptionPage Overview Hardware Preparation and InstallationBefore Installation Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsFeature Operating Non-Operating packed state DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature ValueConfiguring the Module Switch LocationInstalling and Removing the Module Switch SettingsSwitch Hardware Upgrades and Acessories Installation ProcedureRemoval Procedure Controls, LEDs and Connectors Front Panel Connectors and LEDsLayout Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMAccess Access and Configuration CablingCabling MIB Browser Settings Using a MIB BrowserConfiguring the PMC-CGM Using a MIB Browser Access and ConfigurationDefining the IP address of the protection partner module Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining Snmp Trap DestinationsConfiguring the interface mode Configure the Interface ModeConfigure the Bits Interface Configuring the Bits interfaceConfiguring the initial master/slave roles Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Setting up a multi-shelf configurationConfigure the Reference Clock Configuring the reference clock source for the T0/T4 pathConfigure the Reference Clock Access and Configuration Perform Firmware/Software Upgrade Upgrading the firmware/softwareReset the PMC-CGM Resetting the PMC-CGM via SnmpReset the PMC-CGM Access and Configuration Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Structure MIB DescriptionCgmControl CgmInputTableMIB DescriptioncgmControl DefaultInput Assignments Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys MIB Description CgmSysCgmEventTable Not supported on PMC-CGMEvent Codes and Severity MIB DescriptioncgmSysCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistCgmClkDist Objects CgmClkDist MIB DescriptionNot applicable for PMC-CGM PLL Related Documentation Emerson Network Power Embedded Computing DocumentsRelated Specifications Document Title Publication NumberPage Index Sonet