Emerson Using a MIB Browser, Configuring the PMC-CGM, MIB Browser Settings, Setting Value

Page 37

Using a MIB Browser

Access and Configuration

 

 

4.3Using a MIB Browser

When you are using a MIB browser to configure the PMC-CGM, you have to use the following settings.

Table 4-1 MIB Browser Settings

Setting

Value

 

 

Read community

Public

 

 

Write community

Public

 

 

Dynamic IP addresses

172.17.<SGA>.18: acces via ETHA on left ARTM-F103-STX

assigned by ATCA-M100

172.18.<SGA>.18: acces via ETHB on left ARTM-F103-STX

 

 

172.17.<SGA>.28: acces via ETHB on right ARTM-F103-STX

 

172.18.<SGA>.28: acces via ETHA on right ARTM-F103-STX

 

The first three octets of the IP addresses correspond to the first three

 

octets of the shelf manager IP connection record (SMICR) which is part

 

of the chassis FRU. It can be extracted by the ShM of your system. For

 

details of the SMICR refer to the PICMG 3.0 Rev. 1.0 AdvancedTCA Base

 

Specification.

 

 

All changes that you apply via the MIB browser are volatile, that means they are lost when the module is rebooted. The only exception is the cgmBootString (OID:.1.3.6.1.4.1.3656.8152.1.3.33) object, which is stored in the NVRAM.

4.4Configuring the PMC-CGM

To configure the PMC-CGM, you can perform the following tasks which are described in detail in the following sections.

zDefine the IP address of the protection partner module

zDefine SNMP trap destinations

zConfigure the interface mode - SDH/E1 versus SONET/T1

zConfigure the BITS interface

zConfigure the initial master/slave role

zSetup a multishelf configuration

zConfigure the reference clock

zUpgrade the firmware/software

zReset the PMC-CGM

zConfigure parameters for event handling

PMC-CGM Installation and Use (6806800D53C)

37

Image 37
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C About this Manual Overview of ContentsAbbreviations RTM About this Manual Abbreviation DefinitionNotation Description ConventionsBold Comments and Suggestions Summary of ChangesAbout this Manual Notation Description Part Number Publication Date DescriptionElectrical Interference Safety NotesSafety Notes InstallationOperation Cabling and Connectors Configuration SwitchesEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Kabel und Stecker SchaltereinstellungenUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Compliances and Clocking Standards Standard CompliancesIntroduction Standard Compliances Standard DescriptionAvailable Board Variants Ordering InformationOrdering InformationIntroduction Order Number DescriptionPage Before Installation Hardware Preparation and InstallationOverview Unpacking and Inspecting the ModuleRequirements Hardware Preparation and Installation RequirementsRequirementsHardware Preparation and Installation DC Module Power RequirementsFeature Operating Non-Operating packed state Feature ValueSwitch Location Configuring the ModuleSwitch Settings Installing and Removing the ModuleSwitch Installation Procedure Hardware Upgrades and AcessoriesRemoval Procedure Front Panel Connectors and LEDs Controls, LEDs and ConnectorsLayout Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationAccess and Configuration Cabling AccessCabling Configuring the PMC-CGM Using a MIB BrowserMIB Browser Settings Using a MIB Browser Access and ConfigurationDefine Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefining the IP address of the protection partner module Defining Snmp Trap DestinationsConfigure the Bits Interface Configure the Interface ModeConfiguring the interface mode Configuring the Bits interfaceSetup Multi-Shelf Configuration Configure Initial Master/Slave RoleConfiguring the initial master/slave roles Setting up a multi-shelf configurationConfiguring the reference clock source for the T0/T4 path Configure the Reference ClockConfigure the Reference Clock Access and Configuration Upgrading the firmware/software Perform Firmware/Software UpgradeResetting the PMC-CGM via Snmp Reset the PMC-CGMReset the PMC-CGM Access and Configuration Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmControl MIB DescriptionMIB Structure CgmInputTableInput Assignments DefaultMIB DescriptioncgmControl Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl CgmEventTable CgmSysCgmSys MIB Description Not supported on PMC-CGMMIB DescriptioncgmSys Event Codes and SeverityCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistCgmClkDist MIB Description CgmClkDist ObjectsNot applicable for PMC-CGM PLL Related Specifications Emerson Network Power Embedded Computing DocumentsRelated Documentation Document Title Publication NumberPage Index Sonet