Emerson
manual
List of Tables PMC-CGM Installation and Use 6806800D53C
Specification
Install
Default
Configuration Switches
Reset the PMC-CGM
Accessing the PMC-CGM
Controls, LEDs and Connectors
Removal Procedure
Switch Settings
Safety
Page 6
List of Tables
6
PMC-CGM
Installation and Use (6806800D53C)
Page 5
Page 7
Image 6
Page 5
Page 7
Contents
PMC-CGM
Contact Address
Contents
Contents
List of Tables
List of Tables PMC-CGM Installation and Use 6806800D53C
List of Figures
Location of PMC Slot on ATCA-F103
List of Figures PMC-CGM Installation and Use 6806800D53C
Overview of Contents
About this Manual
Abbreviations
About this Manual Abbreviation Definition
RTM
Conventions
Notation Description
Bold
About this Manual Notation Description
Summary of Changes
Comments and Suggestions
Part Number Publication Date Description
Safety Notes
Electrical Interference
Installation
Safety Notes
Operation
Configuration Switches
Cabling and Connectors
Environment
Safety Notes PMC-CGM Installation and Use 6806800D53C
Sicherheitshinweise
EMV
Sicherheitshinweise
Schaltereinstellungen
Kabel und Stecker
Umweltschutz
Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C
Features
Introduction
Introduction Standard Compliances
Standard Compliances
Standard Compliances and Clocking Standards
Standard Description
Ordering InformationIntroduction
Ordering Information
Available Board Variants
Order Number Description
Page
Overview
Hardware Preparation and Installation
Before Installation
Unpacking and Inspecting the Module
Hardware Preparation and Installation Requirements
Requirements
Feature Operating Non-Operating packed state
DC Module Power Requirements
RequirementsHardware Preparation and Installation
Feature Value
Configuring the Module
Switch Location
Installing and Removing the Module
Switch Settings
Switch
Hardware Upgrades and Acessories
Installation Procedure
Removal Procedure
Controls, LEDs and Connectors
Front Panel Connectors and LEDs
Layout
Bits Interface Connectors
Controls, LEDs and Connectors Bits Interface Connectors
LEDs Controls, LEDs and Connectors
LEDs
LED Description
Name Description
Access and Configuration
Accessing the PMC-CGM
Access
Access and Configuration Cabling
Cabling
MIB Browser Settings
Using a MIB Browser
Configuring the PMC-CGM
Using a MIB Browser Access and Configuration
Defining the IP address of the protection partner module
Define IP Address of the Protection Partner Module
Define Snmp Trap Destinations
Defining Snmp Trap Destinations
Configuring the interface mode
Configure the Interface Mode
Configure the Bits Interface
Configuring the Bits interface
Configuring the initial master/slave roles
Configure Initial Master/Slave Role
Setup Multi-Shelf Configuration
Setting up a multi-shelf configuration
Configure the Reference Clock
Configuring the reference clock source for the T0/T4 path
Configure the Reference Clock Access and Configuration
Perform Firmware/Software Upgrade
Upgrading the firmware/software
Reset the PMC-CGM
Resetting the PMC-CGM via Snmp
Reset the PMC-CGM Access and Configuration
Configure Parameters for Event Handling
Configuring event handling parameters
PMC-CGM Installation and Use 6806800D53C
Page
MIB Structure
MIB Description
CgmControl
CgmInputTable
MIB DescriptioncgmControl
Default
Input Assignments
Instance CgmInputNumber CgmInputName CgmInputFrequency
CgmBitsTable
CgmControl MIB Description
Not yet supported
CgmControlMIB Description
Is present. This should only be set for test purposes
Input When in nonrevertive operation 1, a selected
CgmControl Elements
MIB Description CgmControl
CgmSys MIB Description
CgmSys
CgmEventTable
Not supported on PMC-CGM
Event Codes and Severity
MIB DescriptioncgmSys
Code Severity Description
CgmSysMIB Description
CgmSys Objects
New firmware image
CgmClkDist
MIB Description CgmClkDist
CgmClkDist Objects
CgmClkDist MIB Description
Not applicable for PMC-CGM
PLL
Related Documentation
Emerson Network Power Embedded Computing Documents
Related Specifications
Document Title Publication Number
Page
Index
Sonet
Related pages
All Install page
How do I operate my Humax 9000 if it doesn’t respond?
Top
Page
Image
Contents