Emerson PMC-CGM manual About this Manual, Overview of Contents, Abbreviations

Page 9

About this Manual

Overview of Contents

This manual is divided into the following chapters and appendices.

zSafety Notes on page 13 provides safety relevant information when handling the product.

zSicherheitshinweise on page 17 provides a German translation of the Safety Notes section.

zIntroduction on page 21 provides a basic overview of the features of the product.

zHardware Preparation and Installation on page 25 outlines the installation requirements, switch settings, installation and removal procedures.

zControls, LEDs and Connectors on page 31 describes the LEDs, key, and connectors of the product.

zAccess and Configuration on page 35 provides procedures that necessary when handling the product.

zMIB Description on page 47 gives an overview on the Private Emerson CGM-CONTROL- MIB and describes the implemented MIB objects.

zAppendix A, Related Documentation, on page 63 lists related documentation and specifications.

Abbreviations

This document uses the following abbreviations:

 

Abbreviation

Definition

 

 

 

 

 

 

AdvancedTCA

Advanced Telecom Computing Architecture

 

 

 

 

 

 

AIS

Alarm Indication Signal

 

 

 

 

 

 

AMC

Alarm Management Controller

 

 

 

 

 

 

ANSI

American National Standards Institute

 

 

 

 

 

 

BITS

Building Integrated Timing Source

 

 

 

 

 

 

CD-ROM

Compact-Disk Read-Only Memory

 

 

 

 

 

 

CGM

Clock Generator Module

 

 

 

 

 

 

CISPR

Comité Internationale Spécial des Perturbations

 

 

 

Radioelectrotechnique (International Special Committee on Radio

 

 

 

Interference, IEC)

 

 

 

 

 

 

DC

Direct Current

 

 

 

 

 

 

DHCP

Dynamic Host Configuration Protocol

 

 

 

 

 

 

DPLL

Digital Phase-Locked Loop

 

 

 

 

 

 

 

 

 

PMC-CGM Installation and Use (6806800D53C)

9

Image 9
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C Overview of Contents About this ManualAbbreviations RTM About this Manual Abbreviation DefinitionConventions Notation DescriptionBold Comments and Suggestions Summary of ChangesAbout this Manual Notation Description Part Number Publication Date DescriptionElectrical Interference Safety NotesInstallation Safety NotesOperation Configuration Switches Cabling and ConnectorsEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Schaltereinstellungen Kabel und SteckerUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Compliances and Clocking Standards Standard CompliancesIntroduction Standard Compliances Standard DescriptionAvailable Board Variants Ordering InformationOrdering InformationIntroduction Order Number DescriptionPage Before Installation Hardware Preparation and InstallationOverview Unpacking and Inspecting the ModuleRequirements Hardware Preparation and Installation RequirementsRequirementsHardware Preparation and Installation DC Module Power RequirementsFeature Operating Non-Operating packed state Feature ValueSwitch Location Configuring the ModuleInstalling and Removing the Module Switch SettingsSwitch Hardware Upgrades and Acessories Installation ProcedureRemoval Procedure Controls, LEDs and Connectors Front Panel Connectors and LEDsLayout Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationAccess Access and Configuration CablingCabling Configuring the PMC-CGM Using a MIB BrowserMIB Browser Settings Using a MIB Browser Access and ConfigurationDefine Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefining the IP address of the protection partner module Defining Snmp Trap DestinationsConfigure the Bits Interface Configure the Interface ModeConfiguring the interface mode Configuring the Bits interfaceSetup Multi-Shelf Configuration Configure Initial Master/Slave RoleConfiguring the initial master/slave roles Setting up a multi-shelf configurationConfigure the Reference Clock Configuring the reference clock source for the T0/T4 pathConfigure the Reference Clock Access and Configuration Upgrading the firmware/software Perform Firmware/Software UpgradeReset the PMC-CGM Resetting the PMC-CGM via SnmpReset the PMC-CGM Access and Configuration Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmControl MIB DescriptionMIB Structure CgmInputTableInput Assignments DefaultMIB DescriptioncgmControl Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl CgmEventTable CgmSysCgmSys MIB Description Not supported on PMC-CGMEvent Codes and Severity MIB DescriptioncgmSysCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistCgmClkDist Objects CgmClkDist MIB DescriptionNot applicable for PMC-CGM PLL Related Specifications Emerson Network Power Embedded Computing DocumentsRelated Documentation Document Title Publication NumberPage Index Sonet