Emerson PMC-CGM manual Access and Configuration Cabling

Page 36

Access and Configuration

Cabling

 

 

4.2.1Cabling

To access the PMC-CGM, you have to attach an Ethernet cable to the ARTM-F103-STX as shown in the following graphic.

It is mandatory that you connect port ETH7 with ETHA on the same ARTM-F103-STX and that you cross-connect ETH8 with ETHB on the peer ARTM-F103-STX as indicated below.

Figure 4-1 Connecting the ARTM-F103-STX Ethernet Ports

4.2.2Access

To access the module you can either use IPMI or a MIB browser.

For details on how to access the module via IPMI refer to the PMC-CGM: Control via IPMI Programmer’s Reference.

When using a MIB browser, you have to specify the settings described in Using a MIB Browser on page 37.

36

PMC-CGM Installation and Use (6806800D53C)

Page 35 Page 37
Image 36
Page 35 Page 37
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C Overview of Contents About this ManualAbbreviations About this Manual Abbreviation Definition RTMConventions Notation DescriptionBold Summary of Changes Comments and SuggestionsAbout this Manual Notation Description Part Number Publication Date DescriptionSafety Notes Electrical InterferenceInstallation Safety NotesOperation Configuration Switches Cabling and ConnectorsEnvironment Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Schaltereinstellungen Kabel und SteckerUmweltschutz Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionStandard Compliances Standard Compliances and Clocking StandardsIntroduction Standard Compliances Standard DescriptionOrdering Information Available Board VariantsOrdering InformationIntroduction Order Number DescriptionPage Hardware Preparation and Installation Before InstallationOverview Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsDC Module Power Requirements RequirementsHardware Preparation and InstallationFeature Operating Non-Operating packed state Feature ValueConfiguring the Module Switch LocationInstalling and Removing the Module Switch SettingsSwitch Hardware Upgrades and Acessories Installation ProcedureRemoval Procedure Controls, LEDs and Connectors Front Panel Connectors and LEDsLayout Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMAccess Access and Configuration CablingCabling Using a MIB Browser Configuring the PMC-CGMMIB Browser Settings Using a MIB Browser Access and ConfigurationDefine IP Address of the Protection Partner Module Define Snmp Trap DestinationsDefining the IP address of the protection partner module Defining Snmp Trap DestinationsConfigure the Interface Mode Configure the Bits InterfaceConfiguring the interface mode Configuring the Bits interfaceConfigure Initial Master/Slave Role Setup Multi-Shelf ConfigurationConfiguring the initial master/slave roles Setting up a multi-shelf configurationConfigure the Reference Clock Configuring the reference clock source for the T0/T4 pathConfigure the Reference Clock Access and Configuration Perform Firmware/Software Upgrade Upgrading the firmware/softwareReset the PMC-CGM Resetting the PMC-CGM via SnmpReset the PMC-CGM Access and Configuration Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Description CgmControlMIB Structure CgmInputTableDefault Input AssignmentsMIB DescriptioncgmControl Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys CgmEventTableCgmSys MIB Description Not supported on PMC-CGMEvent Codes and Severity MIB DescriptioncgmSysCode Severity Description CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistCgmClkDist Objects CgmClkDist MIB DescriptionNot applicable for PMC-CGM PLL Emerson Network Power Embedded Computing Documents Related SpecificationsRelated Documentation Document Title Publication NumberPage Index Sonet
Top Page Image Contents