Emerson PMC-CGM manual New firmware image

Page 59

cgmSys

MIB Description

 

 

Table 5-8 cgmSys Objects (continued)

OID

MIB Object

Description

Access

 

 

 

 

.1.3.23

cgmSysHwVersion

The hardware revision of the PMC-CGM.

r

 

 

 

 

.1.3.24

cgmSysSwVersion

The firmware revision of the board in the format "x.y.z"

r

 

 

which corresponds to "<major revision>.<minor

 

 

 

revision>.<build count>.

 

 

 

 

 

.1.3.25

cgmRestartCmd

Restarts the module when set to 1. The operation is

r/w

 

 

ignored while a firmware update is ongoing.

 

 

 

After a successful firmware update this will start the

 

 

 

new firmware.

 

 

 

 

 

.1.3.26

cgmFwUpdateHost

The IP address of the TFTP server where the new

r/w

 

 

firmware image is located.

 

 

 

 

 

.1.3.27

cgmFwUpdateFile

The name of the firmware update image to be

r/w

 

 

downloaded from the TFTP server.

 

 

 

 

 

.1.3.28

cgmFwUpdateMd5

The MD5 checksum of the firmware image. This

r/w

 

 

checksum is verified after downloading the TFTP

 

 

 

image and after programming it into the boot flash.

 

 

 

 

 

.1.3.29

cgmFwUpdateOption

Controls how to handle revision numbers of the old and

r/w

 

 

the new firmware image:

 

 

 

If "newer" (0) only images with a version number higher

 

 

 

than the current one can be programmed.

 

 

 

If "newerOrSame" (1), images with the same or a

 

 

 

higher version number can be programmed.

 

 

 

If "allowDowngrade" (2), firmware downgrade is

 

 

 

possible.

 

 

 

If "noVersionCheck" (3), no version check is performed

 

 

 

at all. This allows installing images which do not

 

 

 

contain version information.

 

 

 

Default value is (0).

 

 

 

 

 

.1.3.30

cgmFwUpdateStart

A value of 1 initiates the firmware update. The value

r/w

 

 

remains 1 as long as the update is ongoing.

 

 

 

 

 

.1.3.31

cgmSysTelnetEnable

Enables(1) / disables (0) a telnet server on the module.

r/w

 

 

Used only for debugging purposes.

 

 

 

Default value is (1).

 

 

 

 

 

.1.3.32

cgmTrapDestination

IP address where to send traps to.

r/w

 

 

Default value is the host address specified in the boot

 

 

 

parameters of the PMC-CGM.

 

 

 

 

 

PMC-CGM Installation and Use (6806800D53C)

59

Image 59
Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C Location of PMC Slot on ATCA-F103 List of FiguresList of Figures PMC-CGM Installation and Use 6806800D53C Abbreviations Overview of ContentsAbout this Manual RTM About this Manual Abbreviation DefinitionBold ConventionsNotation Description Part Number Publication Date Description Summary of ChangesComments and Suggestions About this Manual Notation DescriptionElectrical Interference Safety NotesOperation InstallationSafety Notes Environment Configuration SwitchesCabling and Connectors Safety Notes PMC-CGM Installation and Use 6806800D53C EMV SicherheitshinweiseSicherheitshinweise Umweltschutz SchaltereinstellungenKabel und Stecker Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Introduction FeaturesStandard Description Standard CompliancesStandard Compliances and Clocking Standards Introduction Standard CompliancesOrder Number Description Ordering InformationAvailable Board Variants Ordering InformationIntroductionPage Unpacking and Inspecting the Module Hardware Preparation and InstallationBefore Installation OverviewRequirements Hardware Preparation and Installation RequirementsFeature Value DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature Operating Non-Operating packed stateSwitch Location Configuring the ModuleSwitch Installing and Removing the ModuleSwitch Settings Removal Procedure Hardware Upgrades and AcessoriesInstallation Procedure Layout Controls, LEDs and ConnectorsFront Panel Connectors and LEDs Controls, LEDs and Connectors Bits Interface Connectors Bits Interface ConnectorsLEDs LEDs Controls, LEDs and ConnectorsName Description LED DescriptionAccessing the PMC-CGM Access and ConfigurationCabling AccessAccess and Configuration Cabling Using a MIB Browser Access and Configuration Using a MIB BrowserConfiguring the PMC-CGM MIB Browser SettingsDefining Snmp Trap Destinations Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining the IP address of the protection partner moduleConfiguring the Bits interface Configure the Interface ModeConfigure the Bits Interface Configuring the interface modeSetting up a multi-shelf configuration Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Configuring the initial master/slave rolesConfigure the Reference Clock Access and Configuration Configure the Reference ClockConfiguring the reference clock source for the T0/T4 path Upgrading the firmware/software Perform Firmware/Software UpgradeReset the PMC-CGM Access and Configuration Reset the PMC-CGMResetting the PMC-CGM via Snmp Configuring event handling parameters Configure Parameters for Event HandlingPMC-CGM Installation and Use 6806800D53C Page CgmInputTable MIB DescriptionCgmControl MIB StructureInstance CgmInputNumber CgmInputName CgmInputFrequency DefaultInput Assignments MIB DescriptioncgmControlCgmControl MIB Description CgmBitsTableNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes CgmControl Elements Input When in nonrevertive operation 1, a selectedMIB Description CgmControl Not supported on PMC-CGM CgmSysCgmEventTable CgmSys MIB DescriptionCode Severity Description Event Codes and SeverityMIB DescriptioncgmSys CgmSysMIB Description CgmSys Objects New firmware image MIB Description CgmClkDist CgmClkDistNot applicable for PMC-CGM CgmClkDist ObjectsCgmClkDist MIB Description PLL Document Title Publication Number Emerson Network Power Embedded Computing DocumentsRelated Specifications Related DocumentationPage Index Sonet