Emerson PMC-CGM Define IP Address of the Protection Partner Module, Define Snmp Trap Destinations

Page 38

Access and Configuration	Define IP Address of the Protection Partner Module

You can perform these tasks independently from each other.

4.4.1Define IP Address of the Protection Partner Module

The PMC-CGM modules usually work in a master/slave configuration. The protection partner is the other PMC-CGM module, regardless of the master/slave role. The default partner address is configured according to the IP address configuration described in Table "MIB Browser Settings" on page 37.

Defining the IP address of the protection partner module

To define the IP address via the MIB, process as follows:

1.Start SNMP manager or MIB browser.

2.Connect to the PMC-CGM using one of its IP addresses.

3.In object cgmProtectionPartnerAddress OID: .1.3.6.1.4.1.3656.8152.1.1.22.0 set the IP address of the partner PMC-CGM module.

4.4.2Define SNMP Trap Destinations

The PMC-CGM firmware keeps an event log which captures errors, warnings and informative messages in a RAM buffer. The event log can always be accessed via SNMP. Additionally, it is possible to configure the firmware so that each entry up to a certain severity level is posted as an SNMP trap to a specified destination.

Defining SNMP Trap Destinations

To define SNMP trap destinations, proceed as follows:

1.Start SNMP manager or MIB browser.

2.Connect to the PMC-CGM using one of its IP addresses.

3.Go to object cgmBootString OID:.1.3.6.1.4.1.3656.8152.1.3.33.

4.Enter IP address to which the SNMP traps have to be sent in the hhosttrapDest parameter.

This setting is stored persitently in the NVRAM of the module and is applied after the next reboot.

5.Go to object cgmTrapDestination OID: .1.3.6.1.4.1.3656.8152.1.3.32.0.

6.Enter IP address to which the SNMP traps have to be sent.

This setting is only valid until the next reboot. After the reboot, the default IP address defined via the cgmBootString object is applied.

38	PMC-CGM Installation and Use (6806800D53C)

Image 38

Contents PMC-CGM Contact Address Contents Contents List of Tables List of Tables PMC-CGM Installation and Use 6806800D53C List of Figures Location of PMC Slot on ATCA-F103List of Figures PMC-CGM Installation and Use 6806800D53C Abbreviations Overview of ContentsAbout this Manual About this Manual Abbreviation Definition RTMBold ConventionsNotation Description About this Manual Notation Description Summary of ChangesComments and Suggestions Part Number Publication Date DescriptionSafety Notes Electrical InterferenceOperation InstallationSafety Notes Environment Configuration SwitchesCabling and Connectors Safety Notes PMC-CGM Installation and Use 6806800D53C Sicherheitshinweise EMVSicherheitshinweise Umweltschutz SchaltereinstellungenKabel und Stecker Sicherheitshinweise PMC-CGM Installation and Use 6806800D53C Features IntroductionIntroduction Standard Compliances Standard CompliancesStandard Compliances and Clocking Standards Standard DescriptionOrdering InformationIntroduction Ordering InformationAvailable Board Variants Order Number DescriptionPage Overview Hardware Preparation and InstallationBefore Installation Unpacking and Inspecting the ModuleHardware Preparation and Installation Requirements RequirementsFeature Operating Non-Operating packed state DC Module Power RequirementsRequirementsHardware Preparation and Installation Feature ValueConfiguring the Module Switch LocationSwitch Installing and Removing the ModuleSwitch Settings Removal Procedure Hardware Upgrades and AcessoriesInstallation Procedure Layout Controls, LEDs and ConnectorsFront Panel Connectors and LEDs Bits Interface Connectors Controls, LEDs and Connectors Bits Interface ConnectorsLEDs Controls, LEDs and Connectors LEDsLED Description Name DescriptionAccess and Configuration Accessing the PMC-CGMCabling AccessAccess and Configuration Cabling MIB Browser Settings Using a MIB BrowserConfiguring the PMC-CGM Using a MIB Browser Access and ConfigurationDefining the IP address of the protection partner module Define IP Address of the Protection Partner ModuleDefine Snmp Trap Destinations Defining Snmp Trap DestinationsConfiguring the interface mode Configure the Interface ModeConfigure the Bits Interface Configuring the Bits interfaceConfiguring the initial master/slave roles Configure Initial Master/Slave RoleSetup Multi-Shelf Configuration Setting up a multi-shelf configurationConfigure the Reference Clock Access and Configuration Configure the Reference ClockConfiguring the reference clock source for the T0/T4 path Perform Firmware/Software Upgrade Upgrading the firmware/softwareReset the PMC-CGM Access and Configuration Reset the PMC-CGMResetting the PMC-CGM via Snmp Configure Parameters for Event Handling Configuring event handling parametersPMC-CGM Installation and Use 6806800D53C Page MIB Structure MIB DescriptionCgmControl CgmInputTableMIB DescriptioncgmControl DefaultInput Assignments Instance CgmInputNumber CgmInputName CgmInputFrequencyCgmBitsTable CgmControl MIB DescriptionNot yet supported CgmControlMIB Description Is present. This should only be set for test purposes Input When in nonrevertive operation 1, a selected CgmControl ElementsMIB Description CgmControl CgmSys MIB Description CgmSysCgmEventTable Not supported on PMC-CGMCode Severity Description Event Codes and SeverityMIB DescriptioncgmSys CgmSysMIB Description CgmSys Objects New firmware image CgmClkDist MIB Description CgmClkDistNot applicable for PMC-CGM CgmClkDist ObjectsCgmClkDist MIB Description PLL Related Documentation Emerson Network Power Embedded Computing DocumentsRelated Specifications Document Title Publication NumberPage Index Sonet