IBM UPS1500TLV 750THV, 1000THV 750THV, 1000THV and 1500THV models, Els, Low sensitivity, Utes

3:USER CONFIGURABLE ITEMS

NOTE: SETTINGS ARE MADE THROUGH THE SUPPLIED POWERCHUTE SOFTWARE OR

OPTIONAL SMART SLOT ACCESSORY CARDS. REFER TO THE SOFTWARE HELP GUIDES FOR DETAILS.

FUNCTION	FACTORY	USER SELECTABLE		DESCRIPTION
	DEFAULT	CHOICES
Automatic Self-Test	Every 14 days	Every 14 days	This function sets the interval at which the
	(336 hours)	(336 hours),	uninterruptible power supply will execute a
		Every 7 days	self-test.
		(168 hours),
		On Startup Only,
		No Self-Test
UPS ID	UPS_IDEN	Up to eight characters	Use this field to uniquely identify the unin-
			terruptible power supply, (i.e. server name
			or location) for network management pur-
			poses.
Date of Last Battery	Manufacture Date	mm/dd/yy	Reset this date when you replace the battery
Replacement			module.
Minimum Capacity	0 percent	0, 15, 30, 45, 50, 60, 75,	The uninterruptible power supply will
Before Return from		90 percent	charge its batteries to the specified percent-
Shutdown			age before it powers up connected equip-
			ment, following a low-battery shutdown.
Alarm Control	Enable	Enable, Mute, Disable	User can mute an ongoing alarm or disable
			all existing alarms permanently.
Shutdown Delay	90 seconds	0, 90, 180, 270, 360,	The interval is set between the times when
		450, 540, 630 seconds	the uninterruptible power supply receives a
			shutdown command and actual shutdown.
Synchronized Turn-on	0 seconds	0, 60, 120, 180, 240,	The uninterruptible power supply will wait
Delay		300, 360, 420 seconds	the specified time after the return of utility
			power before turn-on (to avoid branch cir-
			cuit overload).
Output Voltage	750THV, 1000THV	750THV, 1000THV and	750THV, 1000THV and 1500THV models:
	and 1500THV mod-	1500THV models:	Allows the user to select the output voltage.
	els:	220, 230, 240VAC
	230VAC
Voltage Sensitivity	High	: Brightly illumi-	Adjust by pressing the voltage sensitivity
The uninterruptible			button	(rear panel). Use a pointed ob-
		nated - high sensitivity.
power supply detects			ject (such as a pen) to do so.
and reacts to line voltage		: Dimly illuminated	Note: In situations of poor power quality,
distortions by transfer-		- medium sensitivity.
			the uninterruptible power supply may fre-
ring to battery operation
		: No illumination;	quently transfer to battery operation. If the
to protect connected
			connected equipment can operate normally
equipment.		low sensitivity.
			under such conditions, reduce the sensitivity
			setting to conserve battery capacity and
			service life.
Low Battery Warning			The uninterruptible power supply will beep
	2 minutes	: Brightly illumi-	when two minutes of battery runtime re-
	PowerChute software	nated - low battery	mains.
		warning level of about	Change the warning interval setting by
	provides automatic,
		two minutes.
	unattended shutdown		pressing the voltage sensitivity button, while
	when approximately	: Dimly illuminated	pressing and holding the		button.
	two minutes of bat-
	tery operated runtime	- low battery warning	Change the low battery warning interval
		level of about five min-
	remains.
		utes.	setting to the time that the operating system
			or system software requires to safely shut
		: No illumination;	down.
		low battery warning
		level is approximately
		eight minutes.
		Possible interval set-
		tings: 2, 5, 8, 11, 14, 17,
		20, 23 minutes.

9