Tripp Lite SMART2500XLHG owner manual Basic Operation, Buttons Front Panel

Page 7

Basic Operation

Buttons (Front Panel)

“ON/OFF/STANDBY” Button

•To turn the UPS ON: With the UPS plugged into a live AC wall outlet*, press and hold the “ON/OFF/STANDBY” button for one second.** Release the button. If utility power is absent, you can “cold-start” the UPS

(i.e.: turn it ON and supply power for a limited time from its batteries***) by pressing and holding the “ON/OFF/STANDBY” button for one second.**

•To turn the UPS OFF: With the UPS ON and receiving utility power, press and hold the “ON/OFF/STANDBY” button for one second.** Then unplug the UPS from the wall outlet. The UPS will be completely OFF.

*After you plug the UPS into a live AC outlet, the UPS (in ”Standby” mode) will automatically charge its batteries, but will not supply power to its outlets until it is turned ON.

**The alarm will beep once briefly after the indicated interval has passed.

***If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: Briefly press and release the MUTE/ TEST button.

Note: To permanently disable audible UPS alarms: Contact Tripp Lite support for instructions.

To Run a Self-Test: With your UPS plugged in and turned ON, press and hold the MUTE/TEST button. Continue holding the button until the alarm beeps several times and the UPS performs a self test. See “Results of a Self-Test” below.

Note: you can leave connected equipment on during a self-test. Your UPS, however, will not perform a self-test if the UPS is not turned on (see “ON/OFF/STANDBY” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove safe electrical grounding and may introduce a damaging surge into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the UPS switches to battery to test its load capacity and battery charge.

•If the red “OUTPUT LOAD LEVEL” LED remains lit and the alarm continues to sound after the test, the UPS’s outlets are overloaded. To clear the overload, unplug some of your equipment and run the self-test repeatedly until the red “OUTPUT LOAD LEVEL” LED is no longer lit and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user immediately following a self-test may cause the UPS to shut down and cease supplying output power in the event of a blackout or brownout.

•If the “BATTERY WARNING” LED remains lit and the alarm continues to sound after the test, the UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self- test. If the LED remains lit, contact Tripp Lite for service. If your UPS requires battery replacement, visit www.tripplite.com to locate the specific Tripp Lite replacement battery for your UPS.

7

12-10-307-93-3181.indb 7

11/2/2012 9:27:47 AM

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Intelligent, Line-Interactive Medical-Grade UPS System UPS Connection Warnings Important Safety InstructionsStatement of Intended Use UPS Location WarningsPackage Contents Turn the UPS on Quick InstallationPlug the UPS into an outlet on a dedicated circuit Plug your equipment Into the UPSUser Interface Optional InstallationUSB and RS-232 Serial Communications EPO Port Connection External Battery ConnectionButtons Front Panel Basic OperationIndicator Lights Front Panel Other UPS Features Rear Panel Guidance and Manufacturer’s Declaration Electrostatic Discharge ESD Storage Storage and ServiceBattery Replacement ServiceConnect new batteries Warranty RegistrationRemove battery cover Remove old batteriesSistema UPS Inteligente, Interactivo de Grado Médico SMART2500XLHGAdvertencias sobre la conexión del UPS Instrucciones de seguridad importantesDeclaración de Uso Indicado Advertencias sobre la ubicación del UPSDesecho del UPS Contenido del EmpaqueAdvertencias sobre la conexión de equipos Advertencias sobre la bateríaEncienda el UPS Instalación rápidaEnchufe el UPS en un tomacorriente en un circuito dedicado Conecte sus equipos En el UPSInstalación opcional Interfaz de UsuarioComunicaciones USB y serie RS-232 Conexión de puerto Instalación opcional continúaConexión de la Batería Externa Botones Panel frontal Operación básicaLuces indicadoras Panel frontal Operación básica continúaOtras funciones del UPS Panel posterior Orientación y Declaración del Fabricante Orientación y Declaración del Fabricante continúa Almacenamiento Almacenamiento y servicioServicio Reemplazo de batería Manuel du propriétaire Mises en garde Connexions de lUPS Mises en garde Emplacement de lUPSDirectives de sécurité importantes Énoncé sur lutilisation prévueÉlimination du système d’alimentation sans coupure UPS Contenu de lemballageMises en garde Connexion déquipement Mises en garde BatterieMettre lUPS sous tension Installation rapideBrancher l’UPS dans une sortie de circuit à usage exclusif Connecter votre Équipement à lUPSInterface utilisateur Installation en optionPorts de communication de série USB et RS-232 Connexion au port EPO Installation en option suiteRaccord du bloc-piles Externe2b Boutons Panneau avant Fonctionnement de baseVoyants indicateurs Panneau avant Fonctionnement de base suiteAutres caractéristiques de lUPS panneau arrière Directives et déclaration du fabricant Directives et déclaration du fabricant suite Entreposage Entreposage et serviceRetirer les piles usagées Remplacement de batterieÉloigner, avec précaution, le panneau avant de l’unité UPS Retirer le couvercle des pilesIndb 11/2/2012 92822 AM
Top Page Image Contents