NAD C 425 STORING, Recalling and Labelling Presets, To Store a Preset, Recalling a Preset

Page 8

Operation

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA

STORING, RECALLING AND LABELLING PRESETS

Up to 30 presets in total can be stored in the C 425’s memory bank; these can be any mix of either AM or FM stations. When scrolling through the presets, empty preset places will be skipped; it is thus possible to go from preset No. 4 to No. 7 without having seen No. 5 and

6.With the presets you can also store whether you want Blend (No. 3) and FM Mute/Mode (No. 5) to be activated as well every time you recall the preset.

To Store a Preset

•Tune to the radio station you wish to enter into a Preset (refer to this chapter’s section 10). If the station is transmitting RDS information, the RDS indicator will light up and station initials or name will be shown in the Display Panel. If a non-RDS station is found, then just the frequency will be shown.

•Select Blend (No. 3) or FM Mute/Mode (No. 5) if desired.

•To store that station as a Preset, press Memory (No. 4). The Preset number and the red "MEMORY" indicator are flashing in the Display Panel. The lowest available empty preset number will be shown. If no other buttons are pressed within 12 seconds, the tuner will revert to its previous state.

•Press Memory again to store the preset. If you wish to assign a different preset number, rotate the PRESET/TUNE control left or right to select the desired preset number. You can overwrite an existing preset. If the preset number already has been assigned, "MEMORY" will stop blinking, but the preset will continue to blink. When you have selected the desired preset number, press Memory again to store the station.

NOTE

You can enter a new station into an unused Preset or over-write an existing programmed Memory Preset. By doing this you will replace all the data previously held on that Preset number. When Memory is pressed during normal operation, the Preset number and the red "MEMORY" indicator will flash in the Display Panel. If no other buttons are pressed within 12 seconds, the tuner will revert to its previous state. The Memory Presets have a memory back-up, so they will remain stored for several weeks even if the Tuner is switched off or unplugged from the mains supply.

RECALLING A PRESET

•To select a Preset station, the C 425 must be in the Preset mode (the display indicates "PRESET"). If not, press the PRESET/TUNE Mode button (No. 8); "PRESET" will now light up in the display.

•Rotate the Tune/Preset control (No. 10) in either direction until the right Preset is found and shown in the Display Panel. Any unused Presets will be skipped; this avoids having to scroll through empty presets.

DELETING A STORED PRESET

You can empty a Preset by deleting the stored information:

•Select the Preset to be emptied.

•Press and hold the Memory button (No. 4) and Display button (No.7) for two seconds. The preset number and the text "DELETE" will flash in the display.

•Press only the display button again (within default time of 5 seconds) to confirm you want to delete this preset. The text "DELETED" and "—" as the Preset number appear in the display for a couple of seconds.

LABELLING A PRESET

When a station is transmitting RDS information, your NAD C 425 will automatically show the station initials when its Preset is used. Although the Tuner automatically shows the frequency of any other AM or non- RDS Preset station, it also allows you to type in the station name to make it easier to identify which station is stored in the Memory Preset.

To enter a name:

1Select the Preset you want to attach a name to.

2Press and hold the Display button (No. 7) for two seconds. The first space in the Station Data area of the Display Panel will flash.

3Rotate the PRESET/TUNE Control (No. 10) in either direction to scroll and select the first character (see Character list below for reference).

4Press Display to move one place to the right to enter the next desired character.

5Rotate the PRESET/TUNE Control again to select the next character in the name and press Memory to store it.

6Repeat steps 3 to 5 until name is complete or all eight places have been filled (up to 8 characters).

7Press Memory once to finish the labelling procedure. Press Memory again to store the completed name.

There are 37 characters available including a blank space.

SPACE

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

0

1

2

3

4

5

6

7

8

9

 

 

 

NOTE

This function is available only for non-RDS stations. RDS Stations will always display their transmitted name and cannot be over-written.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 425 Explanation of Graphical Symbols PrecautionsElectric Power MaintenanceOWNER’S Record Antenna InformationOutdoor Antenna Grounding Rear Panel Connections Figure Front Panel Controls Figure Quick Start Rear Panel Connections FigureFront Panel Controls Figure Tune mode By rotating the PRESET/TUNE Control No STORING, Recalling and Labelling Presets To Store a PresetRecalling a Preset Deleting a Stored Preset12V Trigger Input System Integration RS-232Technical Details RS-232 port uses the following standard pin-out arrangementTroubleshooting Problem Cause Solution Reference65 dB / 65 dB Specifications AM Tuner SectionPhysical Specifications Branchements SUR LE Panneau Arriere CF. Figure Mise EN Marche RapideOu pour trouver une station Commandes SUR LA Face Parlante CF. Figure NotaCommande DE Préréglage / Accordage Preset Mode Station Préréglée Preset Grâce à ce mode, vousRappel Dune Station Préréglée Preset Mise EN Memoire D’UNE Station PreregleeCodes DE Telecommande Suppression D’UNE Station DE LA MemoireMULTI-ZONES Creation D’UNE Designation DE Station PreregleeEntree Asservissement 12 V 12 V Trigger Input Type de connecteurIntégration Système RS-232 Informations TechniquesProblème Cause Solution DepannageCaractéristiques Section Tuner AM Caractéristiques PhysiquesHinweise ZUR Aufstellung SchnellstartRückwandanschlüsse ABB HinweisFrontplattenelemente ABB PRESET/TUNE Control Voreinstellung/Abstimmung TNR SPEICHERN, Abrufen UND Bezeichnen VON Voreinstellungen Speichern Einer VoreinstellungAbrufen VON Voreinstellungen Löschen Einer Gespeicherten VoreinstellungTechnische Details TriggereingangSystemintegration RS-232 Problemlösung Problem Ursache AbhilfeStechnische Daten AM-TUNER Abmessungen UND GewichtPage Aansluitingen OP HET Achterpaneel FIG Opmerkingen Betreffende DE InstallatieSnelstart Bedieningselementen OP HET Frontpaneel FIG Wanneer u afstemt op een radiozender die geen RDSBedieningselement PRESET/TUNE Voorinstelling Te activeren, kan u het automatisch of handmatigOPSLAAN, Oproepen EN HET Benamen VAN Voorinstellingen EEN Voorinstelling OpslaanEEN Voorinstelling Oproepen EEN Voorinstelling UIT HET Geheugen WissenVoorinstelling 12V TriggerSysteemintegratie RS-232 Technische InformatieProblemen Oplossen Probleem Oorzaak OplossingTechnische Gegevens AM-TUNER-DEEL Afmetingen EN Gewicht VAN DE ApparatuurPage Notas Sobre LA Instalacion Inicio RapidoConexiones DEL Panel Trasero VEA FIG NotasControles DEL Panel Delantero VEA FIG Control DE Preajuste / Sintonización PRESET/TUNE MEMORIZACION, Reactivacion Y Etiquetado DE PreajustePara Memorizar UN Preset Borrado DE UN Preset MemorizadoSeleccione el Preset que ha de vaciarse Para Etiquetar UN PresetEntrada 12V Trigger Input Consumo de corriente 10mA Punta central = Fuste =Ntegración DEL Sistema RS-232 Detalles TécnicosProblema Causa Solución Investigacion DE AveriasEspecificaciones Seccion DE Sintonizador AM Especificaciones FisicasPage Avviamento Rapido Collegamenti Pannello Posteriore Vedere LA FIGPower ON/OFF ACCESO/SPENTO TNR 1 vedere la Fig Comandi Pannello Anteriore Vedere LA FIGComando PRESET/TUNE Comando preimpostazione Oppure è possibile inserire la sintonizzazioneCome Cancellare UNA Preimpostazione Memorizzata Come Memorizzare UNA PreimpostazioneCome Richiamare UNA Preimpostazione Come Etichettare UNA PreimpostazioneDettagli Tecnici Tipo di spinaIntegrazione DELL’IMPIANTO RS-232 Problema Causa Soluzione Ricerca GuastiSpecifiche Sezione Sintonizzatore AM Specifiche FisichePage Notas Sobre a Instalação Instalação E Ligação RápidaOu para seleccionar uma estação Ligações do Painel Traseiro Consultar a FIGComandos do Painel Dianteiro Consultar a FIG Nota Para Memorizar UMA PRÉ-SINTONIA Sleep Mode Modo DE Suspensão TNR 1 consultar aComo MEMORIZAR, Chamar E Atribuir UM Nome ÀS PRÉ-SINTONIAS Atribuir UM Nome a UMA PRÉ-SINTONIA Como Chamar UMA PRÉ-SINTONIAEliminar UMA PRÉ-SINTONIA Guardada Preset Pré-sintonia Tune Sintonização Power On Alimentação ligada12V Trigger Input Entrada DE Disparo DE 12 Tipo de fichaResolução DE Problemas Problema Causa SoluçãoEspecificações Secção do Sintonizador DE AM Especificações FísicasTänk PÅ Följande VID Inkoppling SnabbinstruktionAnslutningar PÅ Apparatens Baksida SE FIG ObserveraKontroller PÅ Apparatens Framsida SE FIG LAGRING, Hämtning OCH Namngivning AV Snabbval HUR MAN Lagrar ETT SnabbvalVälj Blend Nr 3 eller FM Mute/Mode Nr 5 om du önskar Hämtning AV SnabbvalInställningar FÖR Specialinstallationer Fjärrkontrollkoder Radering AV ETT Lagrat SnabbvalLagring AV EN Stations Namn Det finns 37 tecken tillgängliga inklusive mellanslagRS-232 kontakten har följande pinkonfiguration KontaktypTekniska Specifikationer Problem Orsak Lösning FelsökningMått Specifikationer AM Mottagardel65 dB, 65 dB Page Manual 07/06
Top Page Image Contents