Runco DTV-947 manual Connections, AC Power mains Cord Connection, Power Check, Switching On/Off

Page 11

CONNECTIONS

AC Power (mains) Cord Connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector on the front of the projector.

See installation instructions before
connecting to the supply
V NOM	120/230 Volt
I MAX	5/2.5 AMP
FREQ	60/50 Hz
OFF ON

Power Check

The power voltage is determined by the sticker on the front of the projector.

Warning!

Verify the power voltage corresponds to that of the wall outlet.

If the wall outlet voltage is different, call a qualified technician for power adaptation of the projector.

See installation instructions before connecting to the supply

V NOM	120/230 Volt
I MAX	5/2.5 AMP
FREQ	60/50 Hz

OFF ON

Switching On/Off

The projector is switched ON and OFF using the power (mains) switch ON/OFF on the local keyboard

Pressed : ON

Not Pressed : OFF

Stand by indication lamp :

No light up : projector switched off

Green color : projector in Operational mode

Red color : projector is in Standby mode.

3-1

Image 11

Contents DTV-947 Page Table of Contents Table of Contents 10-4 10-1Overview 10-1 10-311-1 10-15OWNER’S Record Safety InstructionsInstallation Instructions On SafetyOn servicing Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On installationIR Sensor Location and Function of ControlsRS 232 Input Port RS 232 Output PortFor Future Use IR Transmission IndicatorHelp Not used Sound controls Not usedConnections AC Power mains Cord ConnectionPower Check Switching On/OffVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputRGB3S or RG3sB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select PeakingColor Select Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster ShiftRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsLinearity Size AdjustmentVertical Linearity Adjustment Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentCoarse Convergence Adjustments Vertical corners Fine Convergence AdjustmentsOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Projector SET-UP RuncoProjector Set-up IdentificationChange Language Change passwordTotal Run Time Change Projector Address Power up modeChange Projector Address Change baudrateCopy a Block Memory managementCopy a block Memory ManagementDelete a Block Deletion of blocksDeleting block by block Deletion of all blocksConvergence mid All settings to midpositionUndo all settings to midpos Undo green convergence mid Common SettingsUndo R & B convergence mid Green convergence midCRT RUN in Cycle Projector Warm UP G2 AdjustmentCRT run in cycle Enter to select the projector warm up menu Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Projector warm up12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemCompact, built-in system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemEYE-QTMAutoconvergence Access to EYE-QTMON-SCREEN MenusEYE-QTMMENU Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraAppendix Centering the Camera VerticallyTOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel RGB Output Rear PanelFront and Rear Panel Descriptions Power Input Program Button Remote Control DescriptionDirect Access Buttons LEDComponent Input Connection ExamplesComposite Video Input Video InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsContrast TintColor BrightnessChroma Enhance Menu Description and Navigation SharpnessLuma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA