Runco DTV-947 manual Messages, Warnings, and Failures

Page 46

Messages, Warnings, and Failures

FAILURE

EYE-Q commu-

nication

error

WAIT

starting

up

EYE-Q

FAN FAILED Projector

will switch off

Communication error between EYE-Q and the projector. Call a qualified service technician.

Message during the start up of the EYE-Q is ready to accept commands.

Message when one of the fans are not working anymore. Pro- jector switches to stand-by.

8-2

Image 46

Contents DTV-947 Page Table of Contents Table of Contents 10-3 10-1Overview 10-1 10-410-15 11-1On Safety Safety InstructionsInstallation Instructions OWNER’S RecordOn installation Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On servicingRS 232 Output Port Location and Function of ControlsRS 232 Input Port IR SensorSound controls Not used IR Transmission IndicatorHelp Not used For Future UseSwitching On/Off AC Power mains Cord ConnectionPower Check ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionRgbs or RGsB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalanceColor Select PeakingColor Select Phase Raster Shift Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingCoarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical cornersStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Identification RuncoProjector Set-up Projector SET-UPTotal Run Time Change passwordChange Language Change baudrate Power up modeChange Projector Address Change Projector AddressMemory Management Memory managementCopy a block Copy a BlockDeletion of all blocks Deletion of blocksDeleting block by block Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Green convergence mid Common SettingsUndo R & B convergence mid Undo green convergence midCRT run in cycle G2 AdjustmentCRT RUN in Cycle Projector Warm UP Projector warm up Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEasy-to-use, high precision automatic geometry system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMAutoconvergence EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAppendix Adjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel Front and Rear Panel Descriptions Rear PanelRGB Output Power Input LED Remote Control DescriptionDirect Access Buttons Program ButtonVideo Input Connection ExamplesComposite Video Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationBrightness TintColor ContrastLuma Enhance Menu Description and Navigation SharpnessChroma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA