Runco DTV-947 manual Getting Started, Quick SET-UP Guide

Page 78

QUICK SET-UP GUIDE

Getting Started

To get started using your DTV-947 system, follow these simple steps:

1.Ensure all sources that you are using are properly connected to the controller. This is something your Runco dealer has probably already done for you; if not, please refer to the ‘Connection Examples’ and the owners manuals of each appro- priate source as necessary.

2.Turn on all sources. If a A/V receiver or a Runco OVSS-8 is being used to switch the video, ensure that is also turned on.

3.Turn on the controller. Make sure the Main Power switch (pg. 11-8) is ON, then press the power button on the front of the controller (or the power button on the remote). Ensure the red LED lights up on the front of the controller.

4.Turn on the projector.

5.With the left or right buttons on the front panel or remote, select the desired source. You may also do this by going through the menu (see pg. 11-14).

6.Select the desired aspect ratio by using the up and down buttons on the front panel or the remote. You may also do this by going through the menu (see pg.11-14). For an explanation of Aspect ratios, please refer to pg. 11-18.

11-12

Image 78

Contents DTV-947 Page Table of Contents Table of Contents 10-3 10-1Overview 10-1 10-410-15 11-1On Safety Safety InstructionsInstallation Instructions OWNER’S RecordOn installation Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On servicingRS 232 Output Port Location and Function of ControlsRS 232 Input Port IR SensorSound controls Not used IR Transmission IndicatorHelp Not used For Future UseSwitching On/Off AC Power mains Cord ConnectionPower Check ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionRgbs or RGsB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Color SelectColor Select Phase Raster Shift Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingConvergence Adjustment Coarse Convergence AdjustmentsConvergence Fine Convergence Adjustments Vertical cornersService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Identification RuncoProjector Set-up Projector SET-UPChange password Total Run TimeChange Language Change baudrate Power up modeChange Projector Address Change Projector AddressMemory Management Memory managementCopy a block Copy a BlockDeletion of all blocks Deletion of blocksDeleting block by block Delete a BlockAll settings to midposition Undo all settings to midposConvergence mid Green convergence mid Common SettingsUndo R & B convergence mid Undo green convergence midG2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Projector warm up Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEasy-to-use, high precision automatic geometry system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Compact, built-in systemAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input LED Remote Control DescriptionDirect Access Buttons Program ButtonVideo Input Connection ExamplesComposite Video Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationBrightness TintColor ContrastMenu Description and Navigation Sharpness Luma EnhanceChroma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA