Runco DTV-947 manual Random access adjustment mode selection menu, Picture Tuning, Color Balance

Page 24

Random Access Adjustment Mode

Random access adjustment mode selection menu.

This is the main menu for the Random Access adjustment mode. Through this menu, the following adjustments and features are accessible:

-Picture Tuning

Sync slow/fast (video/s-video) Color Balance

-Geometry Convergence

-Color Select

Picture Tuning

Highlight Picture tuning by pushing the control disc up or down and press ENTER. The Picture tuning menu will be displayed.

Depending on the input source, the ‘Picture tuning’ menu will display different items.

-Color Balance

-Sync slow/fast

-Peaking

Color Balance

The Color Balance function is used to select or adjust the color temperature of white used by the projector.

The Color Balance can be adjusted in two different ways:

-fixed color balance. You have the choice between 3200k (reddish), 5400 K, 6500 K (white), or 9300 K (bluish).

-Custom white and black balance.

Fixed Color Balance

Highlight one of the 4 programmed color temperatures with the control disc and press ENTER to display the desired color balance.

Custom Color Balance

Select custom white balance by pushing the control disc up or down and press ENTER to start the adjustment.

Push the control disc up or down to adjust the red gain and push the control disc to the left or right to adjust the blue gain. A bar scale indicates the amount of adjust- ment.

Select custom black balance with the control disc and press ENTER to start the adjustment.

Push the control disc up or down to adjust the red cut-off and push the control disc to the left or to the right to adjust the blue cut-off.

When the color balance is adjusted, select continue by pushing the control disc up or down and press ENTER.

Sync Fast/Slow Adjustment

The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image.

Highlight SYNC with the control disc and press ENTER to toggle between FAST and SLOW.

Note: SYNC is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video playback equipment, such as a VCR.

ENTER will toggle Sync between FAST and SLOW.

EXIT will return to the Random Access Adjustment menu.

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

COLOR SELECT

Select with or then <ENTER> <EXIT> to return

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : ON

Select with or <ENTER> to accept <EXIT> to return.

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : ON

COLOR BALANCE

FIXED COLOR BALANCE

3200 5400 6500 9300

CUSTOM WHITE BALANCE

CUSTOM BLACK BALANCE

Select with arrow keys

then <ENTER>

You can

 

adjust red with

or

Blue with

or

<EXIT> to return

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : ON

Select with or <ENTER> to accept <EXIT> to return.

6-3

Page 23 Page 25
Image 24
Page 23 Page 25
Contents DTV-947 Page Table of Contents Table of Contents 10-1 Overview 10-110-3 10-410-15 11-1Safety Instructions Installation InstructionsOn Safety OWNER’S RecordMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugOn installation On servicingLocation and Function of Controls RS 232 Input PortRS 232 Output Port IR SensorIR Transmission Indicator Help Not usedSound controls Not used For Future UseAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionConnecting a RGB Analog source Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalancePeaking Color SelectColor Select Geometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingConvergence Adjustment Coarse Convergence AdjustmentsConvergence Fine Convergence Adjustments Vertical cornersService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Runco Projector Set-upIdentification Projector SET-UPChange password Total Run TimeChange Language Power up mode Change Projector AddressChange baudrate Change Projector AddressMemory management Copy a blockMemory Management Copy a BlockDeletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockAll settings to midposition Undo all settings to midposConvergence mid Common Settings Undo R & B convergence midGreen convergence mid Undo green convergence midG2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Nal # pattern and restart the CRT run in option Exit returns to the Path Selection main menuProjector warm up Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEYE-QTMAUTOCONVERGENCE Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input Remote Control Description Direct Access ButtonsLED Program ButtonConnection Examples Composite Video InputVideo Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationTint ColorBrightness ContrastMenu Description and Navigation Sharpness Luma EnhanceChroma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA
Top Page Image Contents