Runco DTV-947 manual Touch-Up, Align on Current Source, Align from Midposition on Current Source

Page 61

EYE-QTMAutoconvergence

TOUCH-UP

When TOUCH-UP is selected, only the static convergence of the currently selected source will be carried out automatically. Follow the steps below to select:

ADJUSTMENT MODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 1

Highlight TOUCH-UP by pushing up or down keys of the con- trol disc;

Press the <ENTER> button to start up the static convergence.

If the process is successfully completed, the projector will return to image display of the current source.

Select with or then <ENTER>.

<EXIT> to return

EYE-Q

 

TOUCH UP

AUTOCONVERGENCE

QUICK AUTOPICTURE

FULL AUTOPICTURE

EYE-Q SETUP

EYE-Q DIAGNOSTICS

Select with

or

then <ENTER>.

<EXIT> to return

ALIGN ON CURRENT SOURCE

When ALIGN is selected, the automatic convergence on the current memory bank will be carried out automatically, starting from the existing settings.

By projecting alternately red and blue line, 25 convergence areas are aligned to the green pattern.

Follow the steps below to select:

Highlight ALIGN below ON CURRENT SOURCE by push- ing up or down keys of the control disc;

Press the <ENTER> button to start up the automatic conver- gence of the entire screen.

If the process is successfully completed, the projector will return to image display of the current source.

Use this option when the convergence is close to proper alignment.

EYE-Q

 

 

 

TOUCH UP

 

 

AUTOCONVERGENCE

 

 

QUICK AUTOPICTURE

 

 

FULL AUTOPICTURE

 

 

EYE-Q SETUP

 

 

EYE-Q DIAGNOSTICS

 

 

Select with

or

 

 

then <ENTER>.

AUTOCONVERGENCE

<EXIT> to return

 

 

ON CURRENT SOURCE:

 

 

ALIGN

 

 

 

ALIGN FROM MIDPOSITION

 

 

ON ALL SOURCES: (XX)

 

 

TOUCH-UP

 

 

ALIGN

 

 

 

ALIGN FROM MIDPOSITION

 

 

STATUS:

 

 

 

ready

 

 

 

Select with

or

 

 

then <ENTER>.

 

 

<EXIT> to return

ALIGN FROM MIDPOSITION ON CURRENT SOURCE

When ALIGN FROM MIDPOSITION is selected, the automatic convergence on the current source will be carried out automatical- ly, but starting from the mid-position settings.

By projecting alternately red and blue lines, 25 convergence areas are aligned to the green pattern.

Follow the steps below to select:

Highlight ALIGN FROM MIDPOSITION by pushing up or down keys of the control disc;

Press the <ENTER> button to start up the automatic conver- gence of the entire screen.

EYE-Q

 

TOUCH UP

AUTOCONVERGENCE

QUICK AUTOPICTURE

FULL AUTOPICTURE

EYE-Q SETUP

EYE-Q DIAGNOSTICS

Select with

or

then <ENTER>.

<EXIT> to return

AUTOCONVERGENCE

ON CURRENT SOURCE:

ALIGN

 

ALIGN FROM MIDPOSITION

ON ALL SOURCES: (XX)

TOUCH-UP

ALIGN

 

ALIGN FROM MIDPOSITION

STATUS:

 

ready

 

Select with

or

then <ENTER>.

<EXIT> to return

If the process is successfully completed, the projector will return to image display of the current source.

Use this option when the convergence is far from proper alignment.

10-11

Page 60 Page 62
Image 61
Page 60 Page 62
Contents DTV-947 Page Table of Contents Table of Contents Overview 10-1 10-110-3 10-411-1 10-15Installation Instructions Safety InstructionsOn Safety OWNER’S RecordPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugOn installation On servicingRS 232 Input Port Location and Function of ControlsRS 232 Output Port IR SensorHelp Not used IR Transmission IndicatorSound controls Not used For Future UsePower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog sourceRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingColor Select Horizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Projector Set-up RuncoIdentification Projector SET-UPTotal Run Time Change passwordChange Language Change Projector Address Power up modeChange baudrate Change Projector AddressCopy a block Memory managementMemory Management Copy a BlockDeleting block by block Deletion of blocksDeletion of all blocks Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence mid Common SettingsGreen convergence mid Undo green convergence midCRT run in cycle G2 AdjustmentCRT RUN in Cycle Projector Warm UP Exit returns to the Path Selection main menu Nal # pattern and restart the CRT run in optionProjector warm up Enter to select the projector warm up menu12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic convergence system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAppendix Adjusting Other Sources TOUCH-UP on TimerReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Front and Rear Panel Descriptions Rear PanelRGB Output Power Input Direct Access Buttons Remote Control DescriptionLED Program ButtonComposite Video Input Connection ExamplesVideo Input Component InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsColor TintBrightness ContrastLuma Enhance Menu Description and Navigation SharpnessChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA
Top Page Image Contents