Runco DTV-947 manual Runco, Projector Set-up, Identification, Projector SET-UP

Page 35

Service Mode

Projector Set-up

Highlight ‘Projector Set-Up’ by pushing the control disc up or down and press ENTER to display the projector set-up menu.

Within the projector set-up menu, the following items can be consolidated or set to the desired setting :

-Identification

-Total run time

-Change password

-Change language

-Change projector address

-Change baudrate

-Power up mode

Identification

Highlight ‘Identification’ with the control disc and press ENTER.

ENTER will start the selected item.

EXIT returns to the Service mode menu.

The ‘Identification’ screen gives information concerning :

-Projector address. To change the address of your projector, contact a qualified service technician.

-Software version.

-Configuration.

Possible installations :

*Front-ceiling

*Front-table

*Rear-ceiling

*Rear-table

-Baud rate PC : transfer speed for communication with an IBM PC (or com- patible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, contact a qualified service technician to make the appropriate changes.

-Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed.

ON : displayed

OFF : not displayed

The status can be changed by pressing the ‘TEXT’ key once on the RCU.

-Serial no. : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

12C DIAGNOSTICS

Select with or then <ENTER> <EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE: operating

RUNCO

DTV - 947

Proj. address : 001

Soft. Version : 6.00

Config. :Ceiling

Front

Baudrate PC : 9600

Text : ON

Serial No. : 103589552

7-2

Image 35

Contents DTV-947 Page Table of Contents Table of Contents 10-4 10-1Overview 10-1 10-311-1 10-15OWNER’S Record Safety InstructionsInstallation Instructions On SafetyOn servicing Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On installationIR Sensor Location and Function of ControlsRS 232 Input Port RS 232 Output PortFor Future Use IR Transmission IndicatorHelp Not used Sound controls Not usedConnections AC Power mains Cord ConnectionPower Check Switching On/OffVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputRGB3S or RG3sB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select PeakingColor Select Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster ShiftRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsLinearity Size AdjustmentVertical Linearity Adjustment Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentCoarse Convergence Adjustments Vertical corners Fine Convergence AdjustmentsOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Projector SET-UP RuncoProjector Set-up IdentificationChange Language Change passwordTotal Run Time Change Projector Address Power up modeChange Projector Address Change baudrateCopy a Block Memory managementCopy a block Memory ManagementDelete a Block Deletion of blocksDeleting block by block Deletion of all blocksConvergence mid All settings to midpositionUndo all settings to midpos Undo green convergence mid Common SettingsUndo R & B convergence mid Green convergence midCRT RUN in Cycle Projector Warm UP G2 AdjustmentCRT run in cycle Enter to select the projector warm up menu Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Projector warm up12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemCompact, built-in system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemEYE-QTMAutoconvergence Access to EYE-QTMON-SCREEN MenusEYE-QTMMENU Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraAppendix Centering the Camera VerticallyTOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel RGB Output Rear PanelFront and Rear Panel Descriptions Power Input Program Button Remote Control DescriptionDirect Access Buttons LEDComponent Input Connection ExamplesComposite Video Input Video InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsContrast TintColor BrightnessChroma Enhance Menu Description and Navigation SharpnessLuma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA