Runco DTV-947 manual Start UP of the Adjustment Mode, Adjustment mode

Page 20

START UP OF THE ADJUSTMENT MODE

Adjustment mode

All picture geometry and convergence adjustments are made while in the ‘Adjustment mode’. Two possible ways to enter the adjustment mode:

a) Using the RCU.

Press the ADJUST key.

The projector displays the path selection menu.

b) Using the local keypad.

Press the ADJUST key.

The projector displays the General access menu.

Use the control disc to highlight enter ADJUST and press ENTER. The path selection menu will be displayed.

ADJUSTEXIT

STANDBY ENTER

	GENERAL ACCESS
		SHARPNESS
		TINT
5	6	COLOR
3	4	BRIGHTNESS
1	2	CONTRAST
Enter ADJUST
	Select with	,
		or
	then <ENTER>.

<EXIT> to return

Note: to adjust the Analog picture control while in the ‘Adjustment mode’, press the ADJUST key. The next General Access menu will be displayed.

Push the control disc up or down to select the analog control to be adjusted and press the ENTER key to confirm.

When the analog control is adjusted the projector returns automatically to the General access menu. When you want to return to the Adjustment mode, press EXIT, otherwise select quit ADJUST and press ENTER to return to opera- tional mode.

You are now in the ‘Adjustment mode’. The control disc is used to make menu selections and also vertical and horizontal adjustments. The ENTER and EXIT keys are used to move forward and backward through the menu structure. The ADJUST key can be used to terminate the adjustment mode while a path selec- tion menu (head menu) is displayed.

There are 5 possible paths to follow once in the Adjustment mode. They are :

INSTALLATION - Installation should be selected if the projector has been relocated and/or a different screen size is desired.

When selecting ‘Installation’, the user or operator will be warned to call a qual- ified technician to perform the installation procedure (see example of projected warning on next page).

GUIDED - Guided should be selected if the user intends to perform a complete alignment of the projected image. All of the necessary geometry and conver- gence adjustments are made in a predetermined sequence.

General Access From Local Keypad

GENERAL ACCESS

SHARPNESS

TINT

COLOR

BRIGHTNESS

CONTRAST

Quit ADJUST

Select with or

then <ENTER> <EXIT> to return

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

EYE-Q

Source 1

Select with or then <ENTER> <EXIT> to return

5-1

Image 20

Contents DTV-947 Page Table of Contents Table of Contents 10-1 Overview 10-110-3 10-410-15 11-1Safety Instructions Installation InstructionsOn Safety OWNER’S RecordMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugOn installation On servicingLocation and Function of Controls RS 232 Input PortRS 232 Output Port IR SensorIR Transmission Indicator Help Not usedSound controls Not used For Future UseAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionConnecting a RGB Analog source Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalanceColor Select PeakingColor Select Geometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingConvergence Convergence AdjustmentCoarse Convergence Adjustments Fine Convergence Adjustments Vertical cornersOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Runco Projector Set-upIdentification Projector SET-UPChange Language Change passwordTotal Run Time Power up mode Change Projector AddressChange baudrate Change Projector AddressMemory management Copy a blockMemory Management Copy a BlockDeletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockConvergence mid All settings to midpositionUndo all settings to midpos Common Settings Undo R & B convergence midGreen convergence mid Undo green convergence midCRT RUN in Cycle Projector Warm UP G2 AdjustmentCRT run in cycle Nal # pattern and restart the CRT run in option Exit returns to the Path Selection main menuProjector warm up Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEYE-QTMAUTOCONVERGENCE Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMAutoconvergence Access to EYE-QTMON-SCREEN MenusEYE-QTMMENU EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyAppendix Centering the Camera VerticallyTOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel RGB Output Rear PanelFront and Rear Panel Descriptions Power Input Remote Control Description Direct Access ButtonsLED Program ButtonConnection Examples Composite Video InputVideo Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationTint ColorBrightness ContrastChroma Enhance Menu Description and Navigation SharpnessLuma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA