Runco DTV-947 manual Geometry Adjustments, Horizontal Phase Adjustment, Phase Raster Shift

Page 26

Random Access Adjustment Mode

Geometry Adjustments

The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color images : Left-right (EW) and Top-Bottom Cor- rections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity and Horizon- tal Phase.

ENTER will display Geometry menu.

EXIT will return to Internal Crosshatch Selection or Setup

Pattern Selection Menu.

ADJUST returns to operational mode.

Highlight GEOMETRY by pushing the control disc up or down and press ENTER to display the geometry menu.

Within the Geometry Adjustment menu, the following adjustments are available :

-Horizontal Phase (not for internal # pattern).

-Raster Shift

-Left-Right Corrections

-Top-Bottom Corrections

-Horizontal Size

-Vertical Linearity

-Vertical Size

-Blanking

The convergence corrections are disabled during geometry corrections. The blanking correc- tions are only enabled during the blanking adjustments.

Horizontal Phase Adjustment

Push the control disc up or down to highlight H PHASE on Geometry menu and the press

ENTER.

Note : No horizontal phase adjustment is available on the internal # pattern.

For external sources :

If the raster shift is correctly adjusted, the H Phase text box is projected in the middle of the raster. At that moment, the “><” icon indicates the middle of the raster.

Adjust the H Phase control until the middle of the projected image is equal with the middle of >< icon.

Note :

- If the genlocked pattern was selected, the external source will be displayed.

A bar scale and a number indicator (between 0 and 100) on the screen give a visual indication of the horizontal phase adjustment.

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

COLOR SELECT

GEOMETRY

H PHASE

RASTER SHIFT

LEFT - RIGHT (E-W)

TOP - BOTTOM (N-S)

SIZE

V LINEARITY

BLANKING

Select with or then <ENTER> <EXIT> to return.

GEOMETRY

HPHASE RASTER SHIFT

LEFT - RIGHT (E-W)

TOP - BOTTOM (N-S)

SIZE

VLINEARITY BLANKING

X

H PHASE

70

ENTER continues to geometry menu.

X

H PHASE

70

Push the control disc to the right to correct

Push the control disc to the left to correct

X

HPHASE 70

6-5

Image 26

Contents DTV-947 Page Table of Contents Table of Contents 10-3 10-1Overview 10-1 10-410-15 11-1On Safety Safety InstructionsInstallation Instructions OWNER’S RecordOn installation Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On servicingRS 232 Output Port Location and Function of ControlsRS 232 Input Port IR SensorSound controls Not used IR Transmission IndicatorHelp Not used For Future UseSwitching On/Off AC Power mains Cord ConnectionPower Check ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionRgbs or RGsB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalanceColor Select PeakingColor Select Phase Raster Shift Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingConvergence Convergence AdjustmentCoarse Convergence Adjustments Fine Convergence Adjustments Vertical cornersOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Identification RuncoProjector Set-up Projector SET-UPChange Language Change passwordTotal Run Time Change baudrate Power up modeChange Projector Address Change Projector AddressMemory Management Memory managementCopy a block Copy a BlockDeletion of all blocks Deletion of blocksDeleting block by block Delete a BlockConvergence mid All settings to midpositionUndo all settings to midpos Green convergence mid Common SettingsUndo R & B convergence mid Undo green convergence midCRT RUN in Cycle Projector Warm UP G2 AdjustmentCRT run in cycle Projector warm up Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEasy-to-use, high precision automatic geometry system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Compact, built-in systemEYE-QTMAutoconvergence Access to EYE-QTMON-SCREEN MenusEYE-QTMMENU EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyAppendix Centering the Camera VerticallyTOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel RGB Output Rear PanelFront and Rear Panel Descriptions Power Input LED Remote Control DescriptionDirect Access Buttons Program ButtonVideo Input Connection ExamplesComposite Video Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationBrightness TintColor ContrastChroma Enhance Menu Description and Navigation SharpnessLuma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA