Runco DTV-947 manual Specifications

Page 67

SPECIFICATIONS

Aspect Ratios:

Anamorphic, Widescreen, 4:3

Lenses:

Fully color corrected and

Bandwidth:

75 MHz

 

filtered HD-145 lenses

Light Output:

1100 lumens/200 ANSI lumens

Cabinet Dimensions:

Width: 22 in./558.80 mm

Optical Resolution:

 

 

Depth: 29 in./736.60 mm

10 line pairs/mm

 

Height: 12 in./304.80 mm

Picture Size:

 

 

Weight: 96 lbs./43.55 kg

5-20 ft. wide

Color Balance:

3200K, 5400K, 6500K,

Power Consumption:

475W

 

9300K, Custom

Power Requirements:

115 VAC, 50/60 Hz

Configurations:

Front or rear, floor or ceiling mount

Safety Regulations:

Complies with: UL, FCC Class ‘B’,

Contrast Ratios:

100:1

 

CE, C-Tick

Convergence:

Dynamic geometry, 25 point zone

Scan Frequency:

15-50 KHz (horizontal)

Convergence Memories: 32

 

37-210 Hz (vertical)

Storage:

10-122oF (-12-50oC)

CRTs:

7” High performance with

Throw Distance:

1.33 x width (widescreens),

 

Astigmatism controls

Environment:

32-104oF (0-40oC)

 

1.40 x width (4:3 screens)

Video Standards:

NTSC (PAL/NTSC Export version)

Humidity:

0-90%, non-condensing

 

 

Inputs:

Component/RGB, Composite,

 

 

 

S-Video

 

 

10-17

Page 66 Page 68
Image 67
Page 66 Page 68
Contents DTV-947 Page Table of Contents Table of Contents 10-4 10-1Overview 10-1 10-311-1 10-15OWNER’S Record Safety InstructionsInstallation Instructions On SafetyOn servicing Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On installationIR Sensor Location and Function of ControlsRS 232 Input Port RS 232 Output PortFor Future Use IR Transmission IndicatorHelp Not used Sound controls Not usedConnections AC Power mains Cord ConnectionPower Check Switching On/OffVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputRGB3S or RG3sB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select PeakingColor Select Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster ShiftRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Projector SET-UP RuncoProjector Set-up IdentificationTotal Run Time Change passwordChange Language Change Projector Address Power up modeChange Projector Address Change baudrateCopy a Block Memory managementCopy a block Memory ManagementDelete a Block Deletion of blocksDeleting block by block Deletion of all blocksUndo all settings to midpos All settings to midpositionConvergence mid Undo green convergence mid Common SettingsUndo R & B convergence mid Green convergence midCRT run in cycle G2 AdjustmentCRT RUN in Cycle Projector Warm UP Enter to select the projector warm up menu Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Projector warm up12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemCompact, built-in system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAppendix Adjusting Other Sources TOUCH-UP on TimerReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Front and Rear Panel Descriptions Rear PanelRGB Output Power Input Program Button Remote Control DescriptionDirect Access Buttons LEDComponent Input Connection ExamplesComposite Video Input Video InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsContrast TintColor BrightnessLuma Enhance Menu Description and Navigation SharpnessChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA
Top Page Image Contents