Runco DTV-947 manual Selecting Setup Pattern, Internal Cross Hatch Pattern

Page 23

Random Access Adjustment Mode

Selecting Setup Pattern

If an external source is connected to the projector, this menu will be displayed. Push the con- trol disc up or down to highlight the desired setup pattern and then press ENTER.

Genlocked pattern : internally generated cross hatch pattern, locked on the external source.

NOTE: The Genlocked pattern will run at the scan rate of the internal scaler unless an exter- nal Hi-Res RGB or component source is used.

Internal # pattern : internally generated cross hatch pattern and locked on internal generat- ed sync signals. (no external source necessary)

ENTER continues to Random Access Adjustment Mode or

Internal # Pattern Selection.

EXIT returns to Path Selection menu.

ADJUST returns to Operational mode.

Choose a setup pattern from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 01

Select with or then <ENTER> <EXIT> to return

If no external source is connected to the projector, the internal cross hatch pattern menu will be displayed.

Note: The menus in the manual are created for the internal scaler, and the ‘Genlocked Pat- tern’ is selected.

Internal Cross Hatch Pattern

The internal # pattern menu will be displayed if the internal cross hatch pattern has been selected or if no source is connected to the projector.

The table below lists the 8 fixed factory preset frequencies available. Another 8 blocks are custom programmable.

Push the control disc up or down to highlight the desired cross hatch frequency. Push the control disc to the left or to the right to scroll to another page. Press ENTER if the desired block is selected.

15.6/50

PAL/SECAM

15.7/60

NTSC

31.2/50

EDTV

31.5/60

IDTV

31.2/50

HDTVEUREKA

31.5/60

HDTV ATV

33.7/60

HDTV HIVISION

15.8/60

EGA 1

21.8/60

EGA 2

31.5/60

VGA 3

31.5/70

XGA 1,2

35.5/97

VGA 4

44.2/70

SUPER VGA 2

48.5/60

SUPER VGA 1

61.0/76

SUPER VGA 3

63.9/76

APOLLO

INTERNAL # PATTERN

kHz / Hz

 

 

15.6/50

PAL/SECAM

15.7/60

NTSC

31.2/50

EDTV

31.5/60

IDTV

31.2/50

HDTV EUREKA

31.5/60

HDTV ATV

Select with

or

scroll with

or

<ENTER> to accept <EXIT> to return

ENTER continues to the Random Access Adjustment Mode. EXIT returns to the Setup Pattern Selection menu.

6-2

Image 23
Contents DTV-947 Page Table of Contents Table of Contents 10-4 10-1Overview 10-1 10-311-1 10-15OWNER’S Record Safety InstructionsInstallation Instructions On SafetyOn servicing Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On installationIR Sensor Location and Function of ControlsRS 232 Input Port RS 232 Output PortFor Future Use IR Transmission IndicatorHelp Not used Sound controls Not usedConnections AC Power mains Cord ConnectionPower Check Switching On/OffVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputRGB3S or RG3sB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select PeakingColor Select Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster ShiftRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsLinearity Size AdjustmentVertical Linearity Adjustment Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentCoarse Convergence Adjustments Vertical corners Fine Convergence AdjustmentsOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Projector SET-UP RuncoProjector Set-up IdentificationChange Language Change passwordTotal Run Time Change Projector Address Power up modeChange Projector Address Change baudrateCopy a Block Memory managementCopy a block Memory ManagementDelete a Block Deletion of blocksDeleting block by block Deletion of all blocksConvergence mid All settings to midpositionUndo all settings to midpos Undo green convergence mid Common SettingsUndo R & B convergence mid Green convergence midCRT RUN in Cycle Projector Warm UP G2 AdjustmentCRT run in cycle Enter to select the projector warm up menu Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Projector warm up12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemCompact, built-in system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemEYE-QTMAutoconvergence Access to EYE-QTMON-SCREEN MenusEYE-QTMMENU Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraAppendix Centering the Camera VerticallyTOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel RGB Output Rear PanelFront and Rear Panel Descriptions Power Input Program Button Remote Control DescriptionDirect Access Buttons LEDComponent Input Connection ExamplesComposite Video Input Video InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsContrast TintColor BrightnessChroma Enhance Menu Description and Navigation SharpnessLuma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA