Runco DTV-947 manual Menu Description and Navigation, Main Menu

Page 80

MENU DESCRIPTION AND NAVIGATION

Main Menu

MAIN MENU

> COMPOSITE		ADJUST
> COMPOSITE		ADJUST
	S-VIDEO										Source selection and
	COMPONENT

											picture quality adjustments
	PASS THROUGH										picture quality adjustments
	PASS THROUGH

	ASPECT RATIO
	ASPECT RATIO
	PASS-THROUGH SETUP									Aspect ratio selection
	PASS-THROUGH SETUP									Aspect ratio selection
										Sets parameters for


										the projector

The main menu (shown above) includes two sections: Source Selection/ Picture quality adjustments and Functional adjustments. Pressing MENU on the front panel or on the remote control will bring up the main menu.

In the menu shown above, Composite video is selected as the current source. This is indicated by an arrow to the left of ‘COMPOSITE’ in the menu. If S-video were selected, for example, the arrow would then be to the left of ‘S-video’.

To select a source, there are two options. First, using the main menu, you can highlight the desired source with the up or down arrows (front panel or remote), then press enter. The Controller will immediately switch to the desired source. The second option is to simply press the LEFT or RIGHT buttons on the remote or front panel (see page 4) while there are no menus on screen.

Note:

There will be no on-screen display when the PASS-THROUGH is used. If you are using the PASS-THROUGH and wish to change sources, simply press the left or right buttons on the remote or front panel.

11-14

Image 80

Contents DTV-947 Page Table of Contents Table of Contents 10-1 Overview 10-110-3 10-410-15 11-1Safety Instructions Installation InstructionsOn Safety OWNER’S RecordMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugOn installation On servicingLocation and Function of Controls RS 232 Input PortRS 232 Output Port IR SensorIR Transmission Indicator Help Not usedSound controls Not used For Future UseAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionConnecting a RGB Analog source Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalanceColor Select PeakingColor Select Geometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingConvergence Convergence AdjustmentCoarse Convergence Adjustments Fine Convergence Adjustments Vertical cornersOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Runco Projector Set-upIdentification Projector SET-UPChange Language Change passwordTotal Run Time Power up mode Change Projector AddressChange baudrate Change Projector AddressMemory management Copy a blockMemory Management Copy a BlockDeletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockConvergence mid All settings to midpositionUndo all settings to midpos Common Settings Undo R & B convergence midGreen convergence mid Undo green convergence midCRT RUN in Cycle Projector Warm UP G2 AdjustmentCRT run in cycle Nal # pattern and restart the CRT run in option Exit returns to the Path Selection main menuProjector warm up Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEYE-QTMAUTOCONVERGENCE Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMAutoconvergence Access to EYE-QTMON-SCREEN MenusEYE-QTMMENU EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyAppendix Centering the Camera VerticallyTOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel RGB Output Rear PanelFront and Rear Panel Descriptions Power Input Remote Control Description Direct Access ButtonsLED Program ButtonConnection Examples Composite Video InputVideo Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationTint ColorBrightness ContrastChroma Enhance Menu Description and Navigation SharpnessLuma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA