Runco DTV-947 manual Picture Quality Adjustments, Menu Description and Navigation

Page 81

MENU DESCRIPTION AND NAVIGATION

Aspect Ratio allows selection of one of the three aspect ratios provided by the controller. You have two options for selecting an aspect ratio: First, highlight ASPECT RATIO on the main menu, then press ENTER. Then select the desired aspect ratio, and again press ENTER. The second option is to simply press the UP or DOWN arrows on the remote or front panel. Doing this will toggle you through the three choices- Anamorphic (16:9), Letterbox and Standard (4:3). For more infor- mation on aspect ratios, please refer to Page 11-18.

Pass Through Setup: The settings for this will tell the projector which source (RGB or Component) and aspect ratio to ‘look at’ when using the pass-through connectiion on the Controller. For example, if using a computer via the Pass-Through port on the Controller, this setting should be ‘Computer’. However, if a DTV decoder with a com- ponent output is used, the setting should be on ‘YUV HDTV’.

Picture Quality Adjustments

MAIN MENU

> COMPOSITE		ADJUST
	S-VIDEO
	COMPONENT
	PASS THROUGH

ASPECT RATIO

DISPLAY CONTROL

TINT COLOR BRIGHTNESS CONTRAST SHARPNESS LUMA ENHANCE CHROMA ENHANCE VCR MODE

Picture quality adjustments are those that change the various parameters of the image, such as COLOR (saturation level) and BRIGHTNESS (black level), among others. Typically, these adjustments should be made only once (during initial calibra- tion) and then left alone. However, if it is necessary to make any adjustments, per- form the following procedure:

In the example above, note that COMPOSITE is the active source. This is indicated by an arrow to the left of the word ‘COMPOSITE’. To make adjustments, highlight the active source (composite in this case) and press ENTER.

Note:

Pressing ENTER after highlighting a different source will switch you to that source instead of making picture quality adjustments.

11-15

Image 81

Contents DTV-947 Page Table of Contents Table of Contents Overview 10-1 10-110-3 10-411-1 10-15Installation Instructions Safety InstructionsOn Safety OWNER’S RecordPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugOn installation On servicingRS 232 Input Port Location and Function of ControlsRS 232 Output Port IR SensorHelp Not used IR Transmission IndicatorSound controls Not used For Future UsePower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog sourceRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePeaking Color SelectColor Select Horizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsSize Adjustment Vertical Linearity AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence AdjustmentsService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Projector Set-up RuncoIdentification Projector SET-UPChange password Total Run TimeChange Language Change Projector Address Power up modeChange baudrate Change Projector AddressCopy a block Memory managementMemory Management Copy a BlockDeleting block by block Deletion of blocksDeletion of all blocks Delete a BlockAll settings to midposition Undo all settings to midposConvergence mid Undo R & B convergence mid Common SettingsGreen convergence mid Undo green convergence midG2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Exit returns to the Path Selection main menu Nal # pattern and restart the CRT run in optionProjector warm up Enter to select the projector warm up menu12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic convergence system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic geometry system Compact, built-in systemAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraCentering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input Direct Access Buttons Remote Control DescriptionLED Program ButtonComposite Video Input Connection ExamplesVideo Input Component InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsColor TintBrightness ContrastMenu Description and Navigation Sharpness Luma EnhanceChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA