Runco DTV-947 manual No Pattern Error, Status Reporting Forced Break, Status Forced break

Page 64

EYE-QTMAutoconvergence

NO PATTERN ERROR

After starting up the automatic convergence, the projector will start to calculate and locate 5 horizontal and 5 vertical lines which are used to divide the screen into 25 areas.

If the projector does not succeed in finding the pattern, it will try two time. If the two attempts fail, the projector will quit the process and display the Error menu.

The AUTOCONVERGENCE selection will be followed by the error window displaying the following possibilities.

Error occurred, please check:

the lens cap is removed

the lens of the camera is correctly focused;

the camera is correctly centered;

if hardware problems exist, do diagnostics;

the ambient light is too high;

the blanking adjustments are correct;

Press the <ENTER> button to start EYE-QTMdiagnostics (refer to page for full details on EYE-QTMdiagnostics, please note that this option may vary in selection with different pro- jectors).

STATUS REPORTING FORCED BREAK

After starting up the automatic convergence, if unexpected trouble such as the interruption of source input occurs, the projector will quit the process and display the AUTOCONVERGENCE menu on the screen.

The status line in the AUTOCONVERGENCE menu will display the following message:

EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
Select with	or
then <ENTER>.
<EXIT> to return

Error occurred

check :

*lenscap removed *focus camera *center camera *ambient light too high

*hardware problem : press <ENTER> to start diagnostics

*blanking adjustments are correct

Press <ENTER>. to start EYE-Q diagnostics or <EXIT> to return

Status: Forced break

The possible causes of such an error:

The source is disconnected during the convergence:

On the screen a message “Source not available” will be dis- played and projector waits until the source is reconnected or selected;

Switching sources during the convergence:

After the source is available again, the AUTOCONVER- GENCE menu will be displayed the status line reporting “Forced Break.”

AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
forced break
Select with	or
then <ENTER>.
<EXIT> to return

10-14

Image 64

Contents DTV-947 Page Table of Contents Table of Contents 10-1 Overview 10-110-3 10-410-15 11-1Safety Instructions Installation InstructionsOn Safety OWNER’S RecordMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugOn installation On servicingLocation and Function of Controls RS 232 Input PortRS 232 Output Port IR SensorIR Transmission Indicator Help Not usedSound controls Not used For Future UseAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionConnecting a RGB Analog source Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalanceColor Select PeakingColor Select Geometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingCoarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical cornersStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Runco Projector Set-upIdentification Projector SET-UPTotal Run Time Change passwordChange Language Power up mode Change Projector AddressChange baudrate Change Projector AddressMemory management Copy a blockMemory Management Copy a BlockDeletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Common Settings Undo R & B convergence midGreen convergence mid Undo green convergence midCRT run in cycle G2 AdjustmentCRT RUN in Cycle Projector Warm UP Nal # pattern and restart the CRT run in option Exit returns to the Path Selection main menuProjector warm up Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEYE-QTMAUTOCONVERGENCE Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMAutoconvergence EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAppendix Adjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel Front and Rear Panel Descriptions Rear PanelRGB Output Power Input Remote Control Description Direct Access ButtonsLED Program ButtonConnection Examples Composite Video InputVideo Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationTint ColorBrightness ContrastLuma Enhance Menu Description and Navigation SharpnessChroma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA