Runco DTV-947 manual MESSAGES, WARNINGS, and Failures

Page 45

MESSAGES, WARNINGS, AND FAILURES

INPUT 01

Fh= 15.6 kHz

Fv= 050 Hz

SOURCE 01

enter password

X X X X

text on

text off

PROJECTOR ADDRESS:

003

PROJECTOR ADDRESS:

003

WARNING:

invalid key entry

When selecting a new source, information about this source will be displayed on the screen. Source number, horizontal and vertical frequencies of the dis- played source.

Announcement of the selected source.

Message to enter your password. Password contains 4 digits.

These messages will be dis- played on the screen when push- ing the TEXT key.

Text ON : the ‘bar scale indica- tion’ will be enabled during the change of an analog control in the ‘operational mode’ + all warnings and failures will be dis- played.

Text OFF : the ‘bar scale indica- tion’ will be disabled during the change of an analog control in the ‘operational mode’ + all warnings and failures will not be displayed.

Indication of the projector address when activating the ‘ADDRESS’ button on the RCU with a pencil or other small object.

The input is a valid input but the source is not connected to the input terminals or the input source is switched off.

When a wrong key is pressed on the RCU.

WARNING:

invalid key entry

WARNING:

end of ad- just range

WARNING: input no longer available

WARNING: invalid

frequency input

table is deleted

FAILURE

I2C error addr.: 7FH3

FAILURE short circuit on 12C bus

Message when the entered pass- word is wrong.

End of adjustment range.

Message will be displayed when the input source is no longer available. The following mes- sage then appears: ‘check input signal or select new source’.

The entered frequency or applied frequency of the source is out of the projector’s range

Message to inform that selected table is deleted. This message will be followed by ‘confirm message’, on which the user has to answer.

Hardware failure. Call a quali- fied service technician for repair.

Hardware failure. Call a quali- fied service technician for repair.

8-1

Image 45

Contents DTV-947 Page Table of Contents Table of Contents Overview 10-1 10-110-3 10-411-1 10-15Installation Instructions Safety InstructionsOn Safety OWNER’S RecordPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugOn installation On servicingRS 232 Input Port Location and Function of ControlsRS 232 Output Port IR SensorHelp Not used IR Transmission IndicatorSound controls Not used For Future UsePower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog sourceRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePeaking Color SelectColor Select Horizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsSize Adjustment Vertical Linearity AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence AdjustmentsService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Projector Set-up RuncoIdentification Projector SET-UPChange password Total Run TimeChange Language Change Projector Address Power up modeChange baudrate Change Projector AddressCopy a block Memory managementMemory Management Copy a BlockDeleting block by block Deletion of blocksDeletion of all blocks Delete a BlockAll settings to midposition Undo all settings to midposConvergence mid Undo R & B convergence mid Common SettingsGreen convergence mid Undo green convergence midG2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Exit returns to the Path Selection main menu Nal # pattern and restart the CRT run in optionProjector warm up Enter to select the projector warm up menu12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic convergence system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic geometry system Compact, built-in systemAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraCentering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input Direct Access Buttons Remote Control DescriptionLED Program ButtonComposite Video Input Connection ExamplesVideo Input Component InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsColor TintBrightness ContrastMenu Description and Navigation Sharpness Luma EnhanceChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA