Runco DTV-947 manual TOUCH-UP on Timer, Reference Source, Adjusting Other Sources

Page 58

EYE-QTMAutoconvergence

TOUCH-UP ON TIMER

This option allows the static convergence to be carried out auto- matically after a user-defined time, which can be programmed in hours and/or minutes.

To program the touch-up on Timer:

Push up or down keys of the control disc to highlight ON TIMER: off;

Press the <ENTER> button to switch it to ON and the preset time will be displayed;

Press the <TEXT> button to enter the TOUCH-UP TIMER menu;

Push left or right keys of the control disc to highlight the digit to be changed;

Use the numeric keys to enter a desire value;

Press the <ENTER> button to confirm and the EYE-QTMSETUP menu will return on the screen; or press the <EXIT> button to leave the preset value untouched and return to the EYE-QTMSETUP menu.

Press the <EXIT> button to return to the EYE-QTMmenu.

When one adjust geometry by hand, a reference screen and a refer- ence pattern are required. There are a lot of possibilities for a ref- erence screen. A test pattern for a video test disc is normally used. See geometry section of manual for more information. Once a selection of a reference screen and a reference pattern is made, adjusting geometry is only a matter of converging these two ele- ments.

EYE-QTMrequires a reference for adjusting geometry. The simplest way to have a reference screen is to adjust one source by hand, which then serves as a reference for all other sources. After adjust- ing a source, the reference is learned by EYE-QTMand stored in non-volatile memory. Having this Reference Source in memory EYE-QTMcan adjust all other sources to have the same geometry as the Reference Source.

EYE-Q

 

TOUCH UP

AUTOCONVERGENCE

QUICK AUTOPICTURE

FULL AUTOPICTURE

EYE-Q SETUP

EYE-Q DIAGNOSTICS

Select with

or

then <ENTER>.

<EXIT> to return

 

EYE-Q SETUP

 

 

FOCUS THE LENS

 

 

CENTER THE CAMERA

 

 

CONFIGURATION: rear/front

 

 

LEARN REFERENCE

 

 

TOUCH-UP OPTIONS:

 

 

TOUCH-UP OPTIONS

 

ON SOURCE SWITCH : on/off

 

ON TIMER : on/off

 

-h.- min.

 

 

Select with

or

 

then <ENTER>.

 

<EXIT> to return

EYE-Q SETUP

 

FOCUS THE LENS

 

CENTER THE CAMERA

 

CONFIGURATION: rear/front

 

LEARN REFERENCE

 

TOUCH-UP OPTIONS:

 

Select with

or

 

then <ENTER>.

 

<EXIT> to return

 

REFERENCE SOURCE

Before any geometric adjustment can be done, the user Must learn a Reference Source. This process is ONLY DONE ONCE since the Reference will be stored in non-volatile memory. If however, the projector is moved from its position, then the Learn Reference pro- cedure must be repeated. After learning a Reference do not touch the camera (for focusing and centering).

If using multi-aspect ratios, a Reference Geometry must be done for each aspect ratio.

ADJUSTING OTHER SOURCES

Once a Reference Source is in memory, other sources are aligned with the same geometry as the Reference Source. If no Reference Source is learned, the resulting geometry will be unpredictable.

10-8

Page 57 Page 59
Image 58
Page 57 Page 59
Contents DTV-947 Page Table of Contents Table of Contents 10-3 10-1Overview 10-1 10-410-15 11-1On Safety Safety InstructionsInstallation Instructions OWNER’S RecordOn installation Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On servicingRS 232 Output Port Location and Function of ControlsRS 232 Input Port IR SensorSound controls Not used IR Transmission IndicatorHelp Not used For Future UseSwitching On/Off AC Power mains Cord ConnectionPower Check ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionRgbs or RGsB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalanceColor Select PeakingColor Select Phase Raster Shift Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingCoarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical cornersStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Identification RuncoProjector Set-up Projector SET-UPTotal Run Time Change passwordChange Language Change baudrate Power up modeChange Projector Address Change Projector AddressMemory Management Memory managementCopy a block Copy a BlockDeletion of all blocks Deletion of blocksDeleting block by block Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Green convergence mid Common SettingsUndo R & B convergence mid Undo green convergence midCRT run in cycle G2 AdjustmentCRT RUN in Cycle Projector Warm UP Projector warm up Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEasy-to-use, high precision automatic geometry system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMAutoconvergence EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAppendix Adjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel Front and Rear Panel Descriptions Rear PanelRGB Output Power Input LED Remote Control DescriptionDirect Access Buttons Program ButtonVideo Input Connection ExamplesComposite Video Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationBrightness TintColor ContrastLuma Enhance Menu Description and Navigation SharpnessChroma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA
Top Page Image Contents