Runco DTV-947 manual Compose

Page 21

Start Up of the Adjustment Mode

RANDOM ACCESS - Random Access should be selected if the user intends to make only a few adjustments.

SERVICE - Service should be selected if the user intends to delete blocks, change pass- word or apply information.

EYE-Q- This selection will only be available when the subconvergence unit EYE-Q is connected to the projector (standard on the DTV-947).

While in Guided or Random Access adjustment Mode, the user may use an external source, an internally generated genlocked pattern or an internally generated multifre- quency cross hatch pattern as a setup pattern. Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks you to enter your password. (Password protection is only available when the password DIP switch on the controller module is in the ON position. Contact a RUNCO authorized technician when no password is requested during the adjustment procedure and password protection is desired.)

Your password contains 4 digits.

a) Adjusting the projector with the RCU.

Enter the digits with the numeric keys on the RCU.

Example : 2 3 1 9

For each digit entered, a ‘X’ appears on the screen under the displayed text ‘enter pass- word’

When your password is correct, you get access to the ‘Adjustment mode’. When the entered password is wrong, the message ‘Wrong password !!!’ will be displayed. The projector stays on the previous selected item.

Factory programmed password : 0000

b) adjusting the projector with the local keypad.

When the ‘compose password’ menu is displayed, select with control disc the first digit of your password and press ENTER. Continue by selecting the second digit with the control disc and press ENTER. Handle in the same way for the third and fourth digit.

When your password is correct, you get access to the ‘Adjustment mode’.

When the entered password is wrong, the message ‘Wrong password’ will be displayed.

Once the password is correctly entered, all other password protected items are accessi- ble without re-entering your password.

When re-entering the adjustment mode, it will be necessary to enter your password again when selecting a password protected item.

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

EYE-Q

Source 1

Select with or then <ENTER> <EXIT> to return

enter password

X X X X

wrong password

COMPOSE

PASSWORD

 

???

 

7

8

9

4

5

6

1

2

3

 

0

 

Select with

,

 

 

or

then <ENTER>

<EXIT> to return

5-2

Page 20 Page 22
Image 21
Page 20 Page 22
Contents DTV-947 Page Table of Contents Table of Contents Overview 10-1 10-110-3 10-411-1 10-15Installation Instructions Safety InstructionsOn Safety OWNER’S RecordPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugOn installation On servicingRS 232 Input Port Location and Function of ControlsRS 232 Output Port IR SensorHelp Not used IR Transmission IndicatorSound controls Not used For Future UsePower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog sourceRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePeaking Color SelectColor Select Horizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsSize Adjustment Vertical Linearity AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence AdjustmentsService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Projector Set-up RuncoIdentification Projector SET-UPChange password Total Run TimeChange Language Change Projector Address Power up modeChange baudrate Change Projector AddressCopy a block Memory managementMemory Management Copy a BlockDeleting block by block Deletion of blocksDeletion of all blocks Delete a BlockAll settings to midposition Undo all settings to midposConvergence mid Undo R & B convergence mid Common SettingsGreen convergence mid Undo green convergence midG2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Exit returns to the Path Selection main menu Nal # pattern and restart the CRT run in optionProjector warm up Enter to select the projector warm up menu12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic convergence system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic geometry system Compact, built-in systemAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraCentering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input Direct Access Buttons Remote Control DescriptionLED Program ButtonComposite Video Input Connection ExamplesVideo Input Component InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsColor TintBrightness ContrastMenu Description and Navigation Sharpness Luma EnhanceChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA
Top Page Image Contents