Runco DTV-947 manual Align from Midposition on ALL Sources, Error Messages

Page 63

EYE-QTMAutoconvergence

ALIGN FROM MIDPOSITION ON ALL SOURCES

When ALIGN FROM MIDPOSITION is selected, the automatic convergence on all sources will be carried out automatically, but starting from the midposition settings.

By projecting alternately red and blue lines, 25 convergence areas are aligned to the green pattern. The process will repeat for as many times as the total number of the sources until all sources are perfectly aligned.

Follow the steps below to select:

Highlight ALIGN FROM MIDPOSITION below ON ALL SOURCES by pushing up or down keys of the control disc;

Press the <ENTER> button to start up the automatic conver- gence of the entire screen.

If the process is successfully completed, the projector will return to image display of the current source.

Use this option when the convergence if far from proper alignment.

EYE-Q

 

TOUCH UP

AUTOCONVERGENCE

QUICK AUTOPICTURE

FULL AUTOPICTURE

EYE-Q SETUP

EYE-Q DIAGNOSTICS

Select with

or

then <ENTER>.

<EXIT> to return

AUTOCONVERGENCE

ON CURRENT SOURCE:

ALIGN

 

ALIGN FROM MIDPOSITION

ON ALL SOURCES: (XX)

TOUCH-UP

ALIGN

 

ALIGN FROM MIDPOSITION

STATUS:

 

ready

 

Select with

or

then <ENTER>.

<EXIT> to return

INTERRUPTING THE AUTOMATIC CONVERGENCE PROCESS

The process of the above-mentioned automatic convergence can be interrupted at any moment by pressing the <EXIT> button.

After the <EXIT> button is pressed, the projector will leave the automatic convergence process and a message will be displayed informing of the action:

Status: Forced<EXIT>

ERROR MESSAGES

The status line in the AUTOCONVERGENCE menu gives three possible messages:

Ready: before automatic convergence starts;

Forced<EXIT>: when interrupting the process;

Forced break: error message.

Error messages are displayed when the automatic convergence is not successfully completed.

AUTOCONVERGENCE

ON CURRENT SOURCE:

ALIGN

 

ALIGN FROM MIDPOSITION

ON ALL SOURCES: (XX)

TOUCH-UP

ALIGN

 

ALIGN FROM MIDPOSITION

STATUS:

 

forced exit

 

Select with

or

then <ENTER>.

<EXIT> to return

AUTOCONVERGENCE

ON CURRENT SOURCE:

ALIGN

 

ALIGN FROM MIDPOSITION

ON ALL SOURCES: (XX)

TOUCH-UP

ALIGN

 

ALIGN FROM MIDPOSITION

STATUS:

 

ready/forced exit/forced break

Select with

or

then <ENTER>.

<EXIT> to return

10-13

Image 63
Contents DTV-947 Page Table of Contents Table of Contents 10-4 10-1Overview 10-1 10-311-1 10-15OWNER’S Record Safety InstructionsInstallation Instructions On SafetyOn servicing Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On installationIR Sensor Location and Function of ControlsRS 232 Input Port RS 232 Output PortFor Future Use IR Transmission IndicatorHelp Not used Sound controls Not usedConnections AC Power mains Cord ConnectionPower Check Switching On/OffVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputRGB3S or RG3sB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentPeaking Color SelectColor Select Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster ShiftRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsSize Adjustment Vertical Linearity AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence AdjustmentsService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Projector SET-UP RuncoProjector Set-up IdentificationChange password Total Run TimeChange Language Change Projector Address Power up modeChange Projector Address Change baudrateCopy a Block Memory managementCopy a block Memory ManagementDelete a Block Deletion of blocksDeleting block by block Deletion of all blocksAll settings to midposition Undo all settings to midposConvergence mid Undo green convergence mid Common SettingsUndo R & B convergence mid Green convergence midG2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Enter to select the projector warm up menu Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Projector warm up12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemCompact, built-in system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraCentering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input Program Button Remote Control DescriptionDirect Access Buttons LEDComponent Input Connection ExamplesComposite Video Input Video InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsContrast TintColor BrightnessMenu Description and Navigation Sharpness Luma EnhanceChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA