Runco DTV-947 manual Total Run Time, Change password, Change Language

Page 36

Service Mode

Total Run Time

Highlight ‘Total Run Time’ with the control disc and press ENTER to dis- play the amount of time the projector has played since its first start up at the factory.

ENTER gives the selected item.

EXIT returns to Service mode menu.

ADJUST returns to the Operational mode.

Note : all projectors leave the factory after a burn-in period of approxi- mately 100 hours.

Change password

This item is password protected.

Highlight ‘Change Password’ with the control disc and press ENTER.

ENTER gives the selected item.

EXIT returns to Service mode menu.

ADJUST returns to the Operational mode.

The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control disc to the left or to the right to select the digits to be changed. Use the numeric keys to enter the new dig- its.

Press ENTER to save the new password. Before saving the new password, a confirmation screen will be displayed.

Press EXIT to return to the Projector Set-up menu without saving the new password.

When the displayed password is correct, press ENTER to save. If not correct, press EXIT to cancel the saving.

ENTER saves the entered password.

EXIT returns without saving.

Change Language

The ‘Change Language’ function offers the possibility to change the lan- guage of the screen menus to :

-English

-Spanish

-French

-German

Highlight ‘Change Language’ with the control disc and press ENTER.

ENTER saves the entered password.

EXIT returns without saving.

Push the control disc up or down to select the desired language and press ENTER to change the language.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE: operating

Select with or then <ENTER> <EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

CHANGE PASSWORD

Enter new password :

CHANGE PASSWORD

Password will be

reprogrammed as XXXX

<ENTER> to confirm <EXIT> to cancel

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

LANGUAGE
ENGLISH
~
ESPANOL
FRANCAIS
DEUTSCH
Select with	or
then <ENTER>
<EXIT> to return.

7-3

Image 36

Contents DTV-947 Page Table of Contents Table of Contents 10-1 Overview 10-110-3 10-410-15 11-1Safety Instructions Installation InstructionsOn Safety OWNER’S RecordMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugOn installation On servicingLocation and Function of Controls RS 232 Input PortRS 232 Output Port IR SensorIR Transmission Indicator Help Not usedSound controls Not used For Future UseAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsConnecting a Composite Video Source to the BNC video input Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionConnecting a RGB Analog source Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port RemoteControlling Controlling Analog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeCompose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalancePeaking Color SelectColor Select Geometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments Left blanking Top blanking Right blanking Bottom blankingConvergence Adjustment Coarse Convergence AdjustmentsConvergence Fine Convergence Adjustments Vertical cornersService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Runco Projector Set-upIdentification Projector SET-UPChange password Total Run TimeChange Language Power up mode Change Projector AddressChange baudrate Change Projector AddressMemory management Copy a blockMemory Management Copy a BlockDeletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockAll settings to midposition Undo all settings to midposConvergence mid Common Settings Undo R & B convergence midGreen convergence mid Undo green convergence midG2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Nal # pattern and restart the CRT run in option Exit returns to the Path Selection main menuProjector warm up Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 ControlSending a Record single instruction Command Code List Decimal valuesSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEYE-QTMAUTOCONVERGENCE Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence EYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learning a Reference Learn ReferenceAdjusting Screen Size On Current SourceTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque AvertissementSafety Tips Features and Benefits General DescriptionFront Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input Remote Control Description Direct Access ButtonsLED Program ButtonConnection Examples Composite Video InputVideo Input Component InputGetting Started Quick SET-UP GuideOverall Functional Description Menu Description and Navigation Main MenuPicture Quality Adjustments Menu Description and NavigationTint ColorBrightness ContrastMenu Description and Navigation Sharpness Luma EnhanceChroma Enhance Aspect Ratios First, the BasicsActive image area Actual screen area Blanked cut off Areas Aspect RatiosTop SideRS-232 Protocol AsciiSpecifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA