Runco DTV-947 manual Change Projector Address, Change baudrate, Power up mode

Page 37

Service Mode

Change Projector Address

Every projector requires an individual address between 0 and 255. This address can be software installed.

To change that address, push the control disc up or down to highlight ‘Change Pro- jector Address’ and press ENTER. The Change Projector Address menu will be displayed and the actual address will be filled in.

ENTER displays the 'Change Projector Address' menu. EXIT returns to the Service mode main menu.

The first digit is highlighted. Select the individual digits by pushing the control disc to the right or to the left. Reprogram with the digit keys on the RCU.

Press ENTER to confirm.

Press EXIT to return the projector set up menu.

Change baudrate

The communication speed between projector and computer has 8 possible speeds. The baud rate speed can be software set up. Highlight ‘Change Baudrate’ by push- ing the control disc up or down and press ENTER to display the Baud rate menu.

The following baud rates are available :

-9600

-4800

-2400

-1200

-600

-300

-150

-110

The actual baud rate will be highlighted. To change the baud rate, push the control disc up or down or to the left or to the right to select the desired baud rate and press ENTER to accept this baud rate.

ENTER to accept the selected baud rate.

EXIT to return without changing the baud rate.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

PROJECTOR ADDRESS

Enter new projector

 

address :

 

0 0 0

 

Use

and

to select,

and reprogram

with numeric keys.

Highest address is 255

<ENTER> to confirm

<EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

BAUDRATE

 

Select new

 

baudrate :

 

9600

4800

2400

1200

600

300

150

110

Select with arrow keys:

<ENTER> to confirm

<EXIT> to return.

Power up mode

When pressing the power switch, the projector can start up in ‘operating mode’ or in ‘stand-by mode’.

Operating mode : the projector start up and displays image.

Stand-by mode : the projector start up in stand-by and waits until the stand-by but- ton or a digit key is pressed.

To change the Power up mode, select Power Up mode by pushing the control disc up or down and press ENTER to toggle between ‘Operating’ and ‘Standby’.

ENTER to toggle between operating and standby.

EXIT to return to the Service menu.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE

POWER UP MODE: operating

Select with or then <ENTER> <EXIT> to return.

7-4

Page 36 Page 38
Image 37
Page 36 Page 38
Contents DTV-947 Page Table of Contents Table of Contents Overview 10-1 10-110-3 10-411-1 10-15Installation Instructions Safety InstructionsOn Safety OWNER’S RecordPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugOn installation On servicingRS 232 Input Port Location and Function of ControlsRS 232 Output Port IR SensorHelp Not used IR Transmission IndicatorSound controls Not used For Future UsePower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog sourceRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingColor Select Horizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Projector Set-up RuncoIdentification Projector SET-UPTotal Run Time Change passwordChange Language Change Projector Address Power up modeChange baudrate Change Projector AddressCopy a block Memory managementMemory Management Copy a BlockDeleting block by block Deletion of blocksDeletion of all blocks Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence mid Common SettingsGreen convergence mid Undo green convergence midCRT run in cycle G2 AdjustmentCRT RUN in Cycle Projector Warm UP Exit returns to the Path Selection main menu Nal # pattern and restart the CRT run in optionProjector warm up Enter to select the projector warm up menu12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic convergence system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAppendix Adjusting Other Sources TOUCH-UP on TimerReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Front and Rear Panel Descriptions Rear PanelRGB Output Power Input Direct Access Buttons Remote Control DescriptionLED Program ButtonComposite Video Input Connection ExamplesVideo Input Component InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsColor TintBrightness ContrastLuma Enhance Menu Description and Navigation SharpnessChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA
Top Page Image Contents