Runco DTV-947 manual Connecting an S-Video or Video source to the S-Video input, Input selection

Page 13

Connections

Connecting an S-Video or Video source to the S-Video input

RS232 IN	RS232 OUT	IR	COMM PORT REMOTE	R	G(s)	B	H	V	VIDEO S - VIDEO This device complies with part 15 of
									the FCC rules. Operation is subject to
									following two conditions (1), This
									device may not cause harmful inter-
									ferance, and (2) this device must
									accept any interferance received
									including interferance that may cause
									undesired operation.

Separate Y-luma/C-Chroma signals for higher quality playback of Super

VHS signals.

Note: S-video should normally be connected to the controller.

Luma / Chroma

VCR S-VIDEO or DVD

4 pin connector configurations:

For S-video:	For video:
Pin 1: earth(ground) luminace	Pin 1: earth(ground) video
Pin 2: earth(ground) chrominance	Pin 2: not connected
Pin 3: luminance signal(Y)	Pin 3: video signal
1Vpp+3dB _	Pin 4: not connected
Pin 4: chrominance signal(C)
_
300mVpp+3dB

Input selection

a. with the RCU: Select “S-Video” in the source selection menu.

b. with the local keypad

-press ADJUST key, the General access menu will be dis played on the screen.

-use the control disk to highlight 2.

-press ENTER to select the highlighted source.

	GENERAL ACCESS
		SHARPNESS
		TINT
5	6	COLOR
3	4	BRIGHTNESS
1	2	CONTRAST
Enter ADJUST
	Select with	,
		or
	then <ENTER>.

<EXIT> to return

FROM LOCAL KEYPAD

3-3

Image 13

Contents DTV-947 Page Table of Contents Table of Contents Overview 10-1 10-110-3 10-411-1 10-15Installation Instructions Safety InstructionsOn Safety OWNER’S RecordPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugOn installation On servicingRS 232 Input Port Location and Function of ControlsRS 232 Output Port IR SensorHelp Not used IR Transmission IndicatorSound controls Not used For Future UsePower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsVideo input selection Connecting a Composite Video Source to the BNC video inputInput selection Connecting an S-Video or Video source to the S-Video inputConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog sourceRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selectionControlling Controlling Pause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingColor Select Horizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Projector Set-up RuncoIdentification Projector SET-UPTotal Run Time Change passwordChange Language Change Projector Address Power up modeChange baudrate Change Projector AddressCopy a block Memory managementMemory Management Copy a BlockDeleting block by block Deletion of blocksDeletion of all blocks Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence mid Common SettingsGreen convergence mid Undo green convergence midCRT run in cycle G2 AdjustmentCRT RUN in Cycle Projector Warm UP Exit returns to the Path Selection main menu Nal # pattern and restart the CRT run in optionProjector warm up Enter to select the projector warm up menu12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware ConfigurationSending a Record single instruction Decimal values Command Code List$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic convergence system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAppendix Adjusting Other Sources TOUCH-UP on TimerReference Source Learn Reference Learning a ReferenceOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement RemarqueSafety Tips General Description Features and BenefitsFront Panel Front and Rear Panel Descriptions Rear PanelRGB Output Power Input Direct Access Buttons Remote Control DescriptionLED Program ButtonComposite Video Input Connection ExamplesVideo Input Component InputQuick SET-UP Guide Getting StartedOverall Functional Description Main Menu Menu Description and NavigationMenu Description and Navigation Picture Quality AdjustmentsColor TintBrightness ContrastLuma Enhance Menu Description and Navigation SharpnessChroma Enhance First, the Basics Aspect RatiosAspect Ratios Active image area Actual screen area Blanked cut off AreasSide TopAscii RS-232 ProtocolSupplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA