Omron CPM1A operation manual Reading/Clearing Error Messages, Buzzer Operation, Key Sequence

Page 94

Programming Console Operations	Section 4-3

4-3-3 Reading/Clearing Error Messages

This operation is used to display and clear error messages. It is possible to dis- play and clear non-fatal errors and MESSAGE instruction messages in any mode, but fatal errors can be cleared in PROGRAM mode only.

	RUN	MONITOR	PROGRAM

	OK	OK	OK
	Before inputting a new program, any error messages recorded in memory
	should be cleared. It is assumed here that the causes of any of the errors for
	which error messages appear have already been taken care of. If the buzzer
	sounds when an attempt is made to clear an error message, eliminate the
	cause of the error, and then clear the error message. (Refer to Section 5 Test
	Runs and Error Processing for troubleshooting information.)
Key Sequence	Follow the procedure below to display and clear messages.

1, 2, 3... 1. Press the CLR Key to bring up the initial display.

2.Press the FUN and then the MONTR Key to begin the operation. If there are no messages, the following display will appear:

ERR/MSG CHK OK

FUN MONTR

If there are messages, the most serious message will be displayed when the MONTR Key is pressed. Pressing MONTR again will clear the present mes- sage and display the next most serious error message. Continue pressing MONTR until all messages have been cleared. These are some examples of error messages:

A memory error:

MONTR

A system error:

MONTR

MEMORY ERR

SYS FAIL FAL01

A message (displayed with MSG(46)):

MONTR

All messages cleared:

MONTR

MATERIAL USED UP

ERR/MSG CHK OK

4-3-4 Buzzer Operation

This operation is used to turn ON and OFF the buzzer that sounds when Pro- gramming Console keys are pressed. This buzzer will also sound whenever an error occurs during PC operation. Buzzer operation for errors is not affected by this setting.

This operation is possible in any mode.

RUN	MONITOR	PROGRAM

OK	OK	OK

82

Image 94

Contents CPM1A CPM1A Programmable Controllers Omron Product References  OmronTable of Contents Appendices About this Manual Precautions Safety Precautions General PrecautionsIntended Audience Operating Environment Precautions Application PrecautionsXiv Application Precautions Backup method Data Concepts EC DirectivesApplicable Directives Conformance to EC DirectivesXviii Section 1 CPM1A Features CPM1A Features and FunctionsSection Standard Peripheral Devices Using the PTNT Link Communications CompoBus/S I/O Link Units Programming is PossibleExpansion I/O Units 2 I/O Terminal and IR Bit AllocationCPU Units Unit Relay output Transistor output Sink type Source type3 CPM1A Functions Control Corresponding IR word Setting range BCDSet value Word Word 001 or later PC model Input bits Response time Mode Function PC model Input bits Min. input pulse widthPulse output single-phase output Temperature Sensor Unit Functions CompoBus/S Slave Functions CPM1A-SRT21CPU Unit and Expansion Unit System ConfigurationCPU Unit and Expansion I/O Unit Configuration CPM1A CPU UnitsExpansion I/O Units Unit Max. number Inputs Outputs Model UnitsHost Link Communications Expansion UnitsConnecting to a Programmable TerminalAdapters and Cables One-to-one PC Link CommunicationsName Usage Model number CompoBus/S I/O Link Connections Name SpecificationsOne-to-one NT Link Communications Peripheral Device ConnectionsSysmac Support Software SYSMAC-CPT Support Name Model numberRevised Specifications Previous specifications New specifications Relevant pagesUnit Specifications and Components General Specifications SpecificationsCPM1A-10CDR-j CPM1A-20CDR-j CPM1A-30CDR-j CPM1A-40CDR-j Characteristics Memory Backup Increment Mode 5 kHz Max 3 I/O SpecificationsCPU Unit Input Specifications SpecificationExpansion I/O Unit Input Specifications CPU Unit and Expansion I/O Unit Output Specifications Relay Output20EDT 8ET Transistor Output Sink TypeTransistor Output Source Type 10CDT1-D 20CDT1-D 30CDT1-D 40CDT1-D 20EDT1 8ET1RS-232C Adapter Specifications Communications Adapter SpecificationsRS-422 Adapter Specifications CPM1A-10CDR-j/10CDT-D/10CDT1-D 10 I/O Terminals Unit ComponentsCPU Unit Components CPM1A-40CDR-j/40CDT-D/40CDT1-D 40 I/O TerminalsFatal error Input indicators Indicator Status MeaningCPU Unit Component Descriptions Expansion I/O Unit with 8 Input Terminals Expansion I/O Unit ComponentsExpansion I/O Unit with 20 I/O Terminals Expansion I/O Unit with 8 Output TerminalsTemperature Sensor Unit Components Analog I/O Unit ComponentsSet value Thermocouple Range C Range F CPM1A-TS001/002CPM1A-TS101/102 Set value Platinum resistance Range C Range FPins Function CompoBus/S I/O Link Unit ComponentsRS-232C Adapter Communications Adapter ComponentsRS-422 Adapter Installation and Wiring Power Supply Voltage Design PrecautionsPower Supply Wiring 4 CPM1A Power InterruptionsMomentary Power Failure Detection Selecting an Installation SiteInstallation Site Conditions Automatic RestartPanel/Cabinet Installation Overheating1 CPM1A Orientation Installing the CPM1A2 CPM1A Installation CorrectDIN Track Installation Installation Connecting an Expansion I/O UnitRemoval Section Line Noise Wiring and ConnectionsGeneral Precautions for Wiring Hanging DuctsConduits Ground WiringFloor Ducts GroundingCrimp Connectors To 240-VAC Power SupplyVDC Power Supply Input Wiring Input ConfigurationCPM1A-8ED Input Wiring Example OutputsDevice Circuit diagram Input DevicesInductive Loads Output Wiring Relay Output WiringOutput Configurations CPM1A-8ER Transistor Output Wiring Sink Type CPM1A-8ET Transistor Output Wiring Source Type CPM1A-40CDT1-DPolarity of Power Supply for the Load Output Short ProtectionInrush Current Considerations Fuse InsertionHost Link Connections Peripheral Device ConnectionOne-to-one Host Link Connection One-to-N Host Link Connection RDB SDB RDA SDA One-to-one PC Link Connections One-to-one NT Link Connections C200HX/HG/HE PC Using Peripheral Devices 2 CPM1A Restrictions and Precautions SSS System SetupSupport Software Capabilities Offline Operations Online EditingFill Group Name Description Go ToCopy PrintGroup Name Description Utility Data Area Lists File Time ChartPC Setup ChangeOnline Operations Offline and Online Operations CQM1-PRO01-E Using a Programming ConsoleCompatible Programming Consoles C200H-PRO27-EDifferent Keys Mode SwitchBuzzer Volume Contrast ControlMonitor Mode Changing the CPM1A’s Mode with the Mode SwitchProgram Mode RUN ModeConnecting the Programming Console Panel InstallationEntering the Password Preparation for OperationProgram Password Program BZ Programming Console Operations OverviewAll Clear Clearing MemoryPartial Clear Buzzer Operation Reading/Clearing Error MessagesKey Sequence OFF Entering or Editing Programs Writing Hexadecimal, BCD Constant Writing a Word Address#FFF6 Writing an Unsigned Decimal NumberWriting a Word Address DM Instruction Search Bit Operand Search00207INSERT END Not Inserting and Deleting InstructionsInsertion Deletion00178CIRCUIT ERR Checking the ProgramDelete END Corrected ProgramCont 11 Bit, Digit, Word MonitorBit Monitor Word MonitorChannel LR Multiple Address MonitoringCLR Channel LR @OFF OFF OFF Differentiation MonitorBinary Monitor CLR OFF OFF OFFThree-word Monitor Signed Decimal Monitor Unsigned Decimal MonitorThree-word Data Modification Changing Timer, Counter SV3CH CHG? Inputting a New SV Constant Hexadecimal, BCD Data ModificationIncrementing and Decrementing a Constant Pres VAL? Binary Data ModificationMontr Signed Decimal Data Modification D0000 MontrForce Set, Reset Unsigned Decimal Data ModificationOn on Clear Force Set/ResetHex-ASCII Display Change 00000FORCE RELE?Displaying the Cycle Time Program PasswordProgramming Example Preparatory Operations00000MEMORY CLR? HR CNT DM Montr END HR CNT DM Programming Procedures Example ProgramInputting the Self-holding Bit Programming ProceduresInputting the One-second Timer Write NOPInputting the Two-second Timer Inputting the 10-count CounterInputting the Flicker Output LD notInputting the END001 Instruction Test Run in Monitor Mode Monitor BZTest Runs and Error Processing Initial System Checks Initial System Checks and Test Run Procedure2 CPM1A Test Run Procedure Points to checkFlash Memory Precautions Error CPM1A CycleSelf-diagnosis Functions Non-fatal ErrorsFatal Errors Message FAL No Meaning and appropriate responseError Messages Identifying ErrorsUser-defined Errors Error FlagsFALS07 Programming Console Operation ErrorsProgramming Errors Message MSG46Type Message Meaning and appropriate response Circuit ERRTroubleshooting Flowcharts Main CheckPower Supply Check Fatal Error Check Follow the Memory ErrorNon-fatal Error Check 121 122 Environmental Conditions Check Memory Error Check Inspection Items Maintenance InspectionsPower supply Allowable voltage fluctuation range Inspection items Details Criteria RemarksStandard Tools Handling PrecautionsNecessary Tools for Inspection Measurement DevicesExpansion Memory Unit Memory Areas PrecautionsOverview ButtonSpecifications Specifications and NomenclatureNomenclature Mounting/Removing Eeprom LED IndicatorHandling Mounting EepromCPM1, CPM1A, CPM2A Peripheral Port Communications SettingsPC Connections CQM1, and SRM1 PCsDisconnecting Uploading ProgramsOperation Procedure Downloading Programs134 135 CPU Units Standard ModelsExpansion Units Expansion I/O UnitsCompoBus/S I/O Link Unit Temperature Sensor UnitsDescription Specifications Model number Communications AdaptersName Appearance Model Number Specifications Peripheral DevicesCPM1A-20CDR-j/20CDT-D/20CDT1-D CPU Unit DimensionsCPM1A-10CDR-j/10CDT-D/10CDT1-D CPU Unit CPM1A-30CDR-j/30CDT-D/30CDT1-D CPU UnitCPM1A-20EDjExpansion I/O Unit CPM1A-40CDR-j/40CDT-D/40CDT1-D CPU UnitCPM1A-8jjjExpansion I/O Unit CPM1A-MAD01 Analog I/O Unit CPM1A-TSjjjTemperature Sensor UnitCPM1A-SRT21 CompoBus/S I/O Link Unit CPM1-CIF01 RS-232C Adapter CPM1-CIF11 RS-422 AdapterDimensions with Peripheral Devices Attached Appendix BAUTOEXEC.BAT ACPAscii BCDBit-control instruction Bit designatorBit number BlockCONFIG.SYS CTSData link DefaultDIP switch Data link areaEeprom EpromFCS Input signal DelayInitialization error InstallJIS LEDLSS Not OFFPCB RAM PromRAS ROM SCPSSS System error Syntax errorSystem configuration System error messageWDT Numbers Index 165 166 167 Revision code Date Revised content Revision History

Related manuals

Manual 6 pages 62.26 Kb