Omron CPM1A Clear Force Set/Reset, Hex-ASCII Display Change, On on, 00000FORCE RELE?

Page 112

Programming Console Operations	Section 4-3

2.Press the SET Key to force the bit ON or press the RESET Key to force the bit OFF.

	0000020000
SET	ON^ ON
	ON^ ON

The cursor in the lower left corner of the display indicates that the force set/ reset is in progress. Bit status will remain ON or OFF only as long as the key is held down; the original status will return one cycle after the key is released.

3.Press the SHIFT and SET Keys or SHIFT and RESET Keys to maintain the status of the bit after the key is released. In this case, the force-set status is indicated by an “S” and the force-reset status is indicated by an “R.”

To return the bit to its original status, press the NOT Key or perform the Clear Force Set/Reset operation. Refer to 4-3-24 Clear Force Set/Reset for details.

Forced status will also be cleared in the following cases:

a)When the PC’s operating mode is changed (although the forced status will not be cleared when the mode is changed between PROGRAM and MONITOR if SR 25211 is ON)

b)When the PC stops because a fatal error occurred

c)When the PC stops because of a power interruption

d)When the Clear Force Set/Reset Operation is performed

4-3-24 Clear Force Set/Reset

This operation is used to restore the status of all bits which have been force set or reset. It is possible in MONITOR or PROGRAM mode only.

RUN	MONITOR	PROGRAM

No	OK	OK

!Caution Before changing the contents of I/O memory, be sure that the changes will not cause equipment to operate unexpectedly or dangerously. In particular, take care when changing the status of output bits. The PC continues to refresh I/O bits even if the PC is in PROGRAM mode, so devices connected to output points on the CPU Unit or Expansion I/O Units may operate unexpectedly.

1, 2, 3... 1. Press the CLR Key to bring up the initial display.

2.Press the SET and then the RESET Key. A confirmation message will appear.

00000FORCE RELE?

SET RESET

Note If you mistakenly press the wrong key, press CLR and start again from the beginning.

3. Press the NOT Key to clear the force-set/reset status of bits in all data areas.

00000FORCE RELE

NOT END

4-3-25 Hex-ASCII Display Change

This operation is used to convert word data displays back and forth between 4-digit hexadecimal data and ASCII. It is possible in any mode.

The displayed PV of the timer or counter cannot be changed.

RUN	MONITOR	PROGRAM

OK	OK	OK

100

Image 112

Contents CPM1A CPM1A Programmable Controllers Omron Product References  OmronTable of Contents Appendices About this Manual Precautions Safety Precautions General PrecautionsIntended Audience Operating Environment Precautions Application PrecautionsXiv Application Precautions Backup method Data EC Directives Applicable DirectivesConcepts Conformance to EC DirectivesXviii Section 1 CPM1A Features CPM1A Features and FunctionsSection Using the PT NT Link Communications CompoBus/S I/O Link UnitsStandard Peripheral Devices Programming is Possible2 I/O Terminal and IR Bit Allocation CPU UnitsExpansion I/O Units Unit Relay output Transistor output Sink type Source type3 CPM1A Functions Control Corresponding IR word Setting range BCDSet value Word Word 001 or later PC model Input bits Response time Mode Function PC model Input bits Min. input pulse widthPulse output single-phase output Temperature Sensor Unit Functions CompoBus/S Slave Functions CPM1A-SRT21System Configuration CPU Unit and Expansion I/O Unit ConfigurationCPU Unit and Expansion Unit CPM1A CPU UnitsExpansion I/O Units Unit Max. number Inputs Outputs Model UnitsHost Link Communications Expansion UnitsConnecting to a Programmable TerminalAdapters and Cables One-to-one PC Link CommunicationsName Usage Model number Name Specifications One-to-one NT Link CommunicationsCompoBus/S I/O Link Connections Peripheral Device ConnectionsSysmac Support Software SYSMAC-CPT Support Name Model numberRevised Specifications Previous specifications New specifications Relevant pagesUnit Specifications and Components General Specifications SpecificationsCPM1A-10CDR-j CPM1A-20CDR-j CPM1A-30CDR-j CPM1A-40CDR-j Characteristics Memory Backup 3 I/O Specifications CPU Unit Input SpecificationsIncrement Mode 5 kHz Max SpecificationExpansion I/O Unit Input Specifications CPU Unit and Expansion I/O Unit Output Specifications Relay OutputTransistor Output Sink Type Transistor Output Source Type20EDT 8ET 10CDT1-D 20CDT1-D 30CDT1-D 40CDT1-D 20EDT1 8ET1RS-232C Adapter Specifications Communications Adapter SpecificationsRS-422 Adapter Specifications Unit Components CPU Unit ComponentsCPM1A-10CDR-j/10CDT-D/10CDT1-D 10 I/O Terminals CPM1A-40CDR-j/40CDT-D/40CDT1-D 40 I/O TerminalsFatal error Input indicators Indicator Status MeaningCPU Unit Component Descriptions Expansion I/O Unit Components Expansion I/O Unit with 20 I/O TerminalsExpansion I/O Unit with 8 Input Terminals Expansion I/O Unit with 8 Output TerminalsTemperature Sensor Unit Components Analog I/O Unit ComponentsCPM1A-TS001/002 CPM1A-TS101/102Set value Thermocouple Range C Range F Set value Platinum resistance Range C Range FPins Function CompoBus/S I/O Link Unit ComponentsRS-232C Adapter Communications Adapter ComponentsRS-422 Adapter Installation and Wiring Design Precautions Power Supply WiringPower Supply Voltage 4 CPM1A Power InterruptionsSelecting an Installation Site Installation Site ConditionsMomentary Power Failure Detection Automatic RestartPanel/Cabinet Installation OverheatingInstalling the CPM1A 2 CPM1A Installation1 CPM1A Orientation CorrectDIN Track Installation Installation Connecting an Expansion I/O UnitRemoval Section Wiring and Connections General Precautions for WiringLine Noise Hanging DuctsGround Wiring Floor DuctsConduits GroundingCrimp Connectors To 240-VAC Power SupplyVDC Power Supply Input Wiring Input ConfigurationCPM1A-8ED Input Wiring Example OutputsDevice Circuit diagram Input DevicesInductive Loads Output Wiring Relay Output WiringOutput Configurations CPM1A-8ER Transistor Output Wiring Sink Type CPM1A-8ET Transistor Output Wiring Source Type CPM1A-40CDT1-DPolarity of Power Supply for the Load Output Short ProtectionInrush Current Considerations Fuse InsertionHost Link Connections Peripheral Device ConnectionOne-to-one Host Link Connection One-to-N Host Link Connection RDB SDB RDA SDA One-to-one PC Link Connections One-to-one NT Link Connections C200HX/HG/HE PC Using Peripheral Devices 2 CPM1A Restrictions and Precautions SSS System SetupSupport Software Capabilities Offline Operations Online EditingGroup Name Description Go To CopyFill PrintFile Time Chart PC SetupGroup Name Description Utility Data Area Lists ChangeOnline Operations Offline and Online Operations Using a Programming Console Compatible Programming ConsolesCQM1-PRO01-E C200H-PRO27-EMode Switch Buzzer VolumeDifferent Keys Contrast ControlChanging the CPM1A’s Mode with the Mode Switch Program ModeMonitor Mode RUN ModeConnecting the Programming Console Panel InstallationEntering the Password Preparation for OperationProgram Password Program BZ Programming Console Operations OverviewAll Clear Clearing MemoryPartial Clear Buzzer Operation Reading/Clearing Error MessagesKey Sequence OFF Entering or Editing Programs Writing Hexadecimal, BCD Constant Writing a Word Address#FFF6 Writing an Unsigned Decimal NumberWriting a Word Address DM Instruction Search Bit Operand SearchInserting and Deleting Instructions Insertion00207INSERT END Not DeletionChecking the Program Delete END00178CIRCUIT ERR Corrected Program11 Bit, Digit, Word Monitor Bit MonitorCont Word MonitorChannel LR Multiple Address MonitoringCLR Channel LR Differentiation Monitor Binary Monitor@OFF OFF OFF CLR OFF OFF OFFThree-word Monitor Signed Decimal Monitor Unsigned Decimal MonitorThree-word Data Modification Changing Timer, Counter SV3CH CHG? Inputting a New SV Constant Hexadecimal, BCD Data ModificationIncrementing and Decrementing a Constant Pres VAL? Binary Data ModificationMontr Signed Decimal Data Modification D0000 MontrForce Set, Reset Unsigned Decimal Data ModificationClear Force Set/Reset Hex-ASCII Display ChangeOn on 00000FORCE RELE?Program Password Programming ExampleDisplaying the Cycle Time Preparatory Operations00000MEMORY CLR? HR CNT DM Montr END HR CNT DM Programming Procedures Example ProgramProgramming Procedures Inputting the One-second TimerInputting the Self-holding Bit Write NOPInputting the Two-second Timer Inputting the 10-count CounterInputting the Flicker Output LD notInputting the END001 Instruction Test Run in Monitor Mode Monitor BZTest Runs and Error Processing Initial System Checks and Test Run Procedure 2 CPM1A Test Run ProcedureInitial System Checks Points to checkFlash Memory Precautions Error CPM1A CycleNon-fatal Errors Fatal ErrorsSelf-diagnosis Functions Message FAL No Meaning and appropriate responseIdentifying Errors User-defined ErrorsError Messages Error FlagsProgramming Console Operation Errors Programming ErrorsFALS07 Message MSG46Type Message Meaning and appropriate response Circuit ERRTroubleshooting Flowcharts Main CheckPower Supply Check Fatal Error Check Follow the Memory ErrorNon-fatal Error Check 121 122 Environmental Conditions Check Memory Error Check Maintenance Inspections Power supply Allowable voltage fluctuation rangeInspection Items Inspection items Details Criteria RemarksHandling Precautions Necessary Tools for InspectionStandard Tools Measurement DevicesExpansion Memory Unit Precautions OverviewMemory Areas ButtonSpecifications Specifications and NomenclatureNomenclature LED Indicator HandlingMounting/Removing Eeprom Mounting EepromPeripheral Port Communications Settings PC ConnectionsCPM1, CPM1A, CPM2A CQM1, and SRM1 PCsDisconnecting Uploading ProgramsOperation Procedure Downloading Programs134 135 Standard Models Expansion UnitsCPU Units Expansion I/O UnitsTemperature Sensor Units Description Specifications Model numberCompoBus/S I/O Link Unit Communications AdaptersName Appearance Model Number Specifications Peripheral DevicesDimensions CPM1A-10CDR-j/10CDT-D/10CDT1-D CPU UnitCPM1A-20CDR-j/20CDT-D/20CDT1-D CPU Unit CPM1A-30CDR-j/30CDT-D/30CDT1-D CPU UnitCPM1A-20EDjExpansion I/O Unit CPM1A-40CDR-j/40CDT-D/40CDT1-D CPU UnitCPM1A-8jjjExpansion I/O Unit CPM1A-MAD01 Analog I/O Unit CPM1A-TSjjjTemperature Sensor UnitCPM1A-SRT21 CompoBus/S I/O Link Unit CPM1-CIF01 RS-232C Adapter CPM1-CIF11 RS-422 AdapterDimensions with Peripheral Devices Attached Appendix BACP AsciiAUTOEXEC.BAT BCDBit designator Bit numberBit-control instruction BlockCONFIG.SYS CTSDefault DIP switchData link Data link areaEeprom EpromFCS Delay Initialization errorInput signal InstallJIS LEDLSS Not OFFPCB RAM PromRAS ROM SCPSSS Syntax error System configurationSystem error System error messageWDT Numbers Index 165 166 167 Revision code Date Revised content Revision History

Related manuals

Manual 6 pages 62.26 Kb