AT&T Remote Port Security Device user manual Connecting the Rpsd Lock to the CO Line

Page 31

You will need the following components to install the RPSD Lock:

■RPSD Lock device

■the CO line assigned as the RMATS channel (on customer premises)

■the PBX modem (on customer premises)

■6 position wire (length depends on local configuration)

■two modular connectors

■two DB25 connectors (male)

■RS-232 cable

■administration terminal

■AC outlet

■RPSD Lock power pack

Connecting the RPSD Lock to the CO Line

The following components are needed to connect the RPSD Lock device to the CO line:

■RPSD Lock

■the CO line assigned as the RMATS channel

■two modular connectors

■6 position wire

■RJ11 connector (for the CO line)

To connect the RPSD Lock device to the CO line, use the following procedure:

1The customer must contact the technical support center to get the port number for the RMATS channel.

2Locate the CO line for the RMATS port where it connects to the modem.

3Install an RJ11 receptacle on the CO line.

4Connect a wired modular connector to the CO line.

5Plug the modular connector on the other end of the wire into the Telco port on the back of the RPSD Lock.

Note: Bypass connectors are optional. See Figure 2-1.

Hardware Installation Procedures

2-13

Image 31

Contents AT&T Trademark Notice Important Safety Instructions Important Safety Instructions Part 15, Subpart a FCC NoticesPart Contents Rpsd System Administration Device LEDs TroubleshootingCables, Connectors, and Ports Table Rpsd Key UseList of Figures List of Tables Getting Started Getting Started Protection Process Rpsd Lock and Key Configuration Responsibilities AudienceTypographical Conventions This Document800 Hotline or Other Service Call Numbers/AddressesInstallation Installation 2Installation Room Layout/Environment Power SupplyLocation of Administration Terminal or Printer Rpsd Lock Hardware ComponentsRpsd Power Monitor Adapter Bypass Connections PBXs Modems Rpsd Lock or Key Administration TerminalRpsd Lock Administration Printer OtherRpsd Key Installing the Rpsd Lock Hardware Installation ProceduresCommon Rpsd Lock Configuration Connecting the Rpsd Lock to the CO Line Connecting the Rpsd Lock to the PBX Modem Rpsd Lock to Modem Rpsd Rpsd Lock to Administratlon Terminal or Printer DTE Powering Up the Rpsd Lock Installing the Rpsd Key Connecting the Rpsd Key to the Modem Connecting the Rpsd Key to the TerminalPowering Up the Rpsd Key Power-Up Behavior of Uninitialized Key Testing an Uninitialized KeyPBX Cables, Connectors, and Ports Table24Installation Software Components Aux. Port SettingsInitializing the Rpsd Lock Initializing an Rpsd Key Test Rpsd Lock Installation Rpsd System Administration Time of Day Access System Activity Log Fields of the System Activity Log entries are Enable/Disable Block AT&T and Other Key Users Single Point AdministrationForce Connect/Disconnect Authorized Keys 6RPSD System Administration Add User Rpsd System Administrator Command SetSyntax Sample Command and Response With Optional Secret Key Sample Command and Response Without Optional Secret KeyBlock User Sample Command and ResponseUnblock User Remove User Test UserList User Table First Sample Command and ResponsePermanent? Second Sample Command and ResponseUser ID Blocked?Third Sample Command and Response Restrid CR Change RestrictionStarthhmm Endhhmm Dayno Start Time LR List RestrictionsN t a Restriction IDUR User Restrictions LH Log History Fields of the Log History screen are Device # AH Access HistoryDuration Date Time User ID Device # FH Failure HistoryReason ST Status Display LS List Statistics FC Force Connect RS Reset StatisticsDate Set FD Force DisconnectID Set Clock SetSC Set Communications Parameters Sample Help Request and Help Response Help ScreensRpsd Key Use Rpsd Key Use Last Call Status Test Access Failure MessagesRpsd Key User Command Set Set Secret Key Set User IDList User Information Set Device NumberHistory Display 08/14/90 08/14/90 131413 Date Changed OK Set Log ID RPSD/KEY11 Status Display10RPSD Key Use Wipe Out Troubleshooting Troubleshooting 2Troubleshooting Access Failure Messages Check described in Testing the Rpsd Lock Access Failure Messages Code Meaning Action 6Troubleshooting Built-in Diagnostics Testing the Rpsd LockLast Call Status Test Self CheckModem Ring Test Hardware ReplacementReplacing the PBX Modem Replacing the Lock or Key 12Troubleshooting Saving the Key Seed Value Cables, Connectors, and Ports Table Xxxxxx PBX Device LEDs Figure B-1 Front Panel LEDsAT&T Definity Rpsd Table B-2 Index Index2Index Index