AT&T Remote Port Security Device user manual CR Change Restriction, Restrid

Page 60

CR - Change Restriction

Syntax:

cr <restr_id,start(hh:mm),end(hh:mm),day_no.> [ RETURN ]

The Change Restriction command is used to set the list of time restrictions that may be placed on a user or users. Time restrictions block access to the RMATS channel for a specified portion of time on a specified day or days. That is, you can block access to the channel, for example, from 10:00AM to 3:00PM on Saturdays and Sundays.

The Change Restriction command is used to set the parameters of the restriction and to define to which code letter (restr_id) the restriction applies. The code is then applied to a specific user or users using the User Restriction command, which is explained in this section. To see which codes correspond to which restrictions, use the List Restrictions command, which is explained in this section.

Note: To set overnight time restrictions you will need to set two separate restrictions from time X until midnight (24:00) on one day and then from time 00:00 to time Y on the next day. For example, if you want to restrict access from 8:00PM on a Thursday until 8:00AM on a Friday, you will need to restrict access from 20:00 on Thursday until 24:00 on Thursday and then restrict access from 00:00 on Friday until 08:00 on Friday. You will also, when you use the User Restrictions command, need to assign both of these restrictions to the users you wish to restrict to prevent overnight access. The first sample below follows this example.

To clear the restrictions from a restriction ID (restr_id), the syntax is

cr <restr_id>, clear

Sample Command and Response:

> cr A,20:00,24:00,4

JPLock01 191 08/16/90 10:20:43 Restr. ‘A’ Set > cr B,00:00,08:00,5

JPLock01 192 08/16/90 10:21:23 Restr. ‘B’ Set

>

The options for the Change Restriction command are:

restr_id	A single character from A-N (a total of 14 possible separate restrictions)
	used as a code to identify a time restriction. The code is then assigned to
	the users you wish to restrict for that period using the User Restrictions
	command described in this section.

3-14RPSD System Administration

Image 60

Contents AT&T Trademark Notice Important Safety Instructions Important Safety Instructions FCC Notices Part 15, Subpart aPart Contents Rpsd System Administration Troubleshooting Cables, Connectors, and Ports TableRpsd Key Use Device LEDsList of Figures List of Tables Getting Started Getting Started Protection Process Rpsd Lock and Key Configuration Audience ResponsibilitiesThis Document Typographical ConventionsHotline or Other Service Call Numbers/Addresses 800Installation Installation 2Installation Power Supply Room Layout/EnvironmentLocation of Administration Terminal or Printer Hardware Components Rpsd LockRpsd Power Monitor Adapter Bypass Connections PBXs Rpsd Lock or Key Administration Terminal Rpsd Lock Administration PrinterOther ModemsRpsd Key Hardware Installation Procedures Installing the Rpsd LockCommon Rpsd Lock Configuration Connecting the Rpsd Lock to the CO Line Connecting the Rpsd Lock to the PBX Modem Rpsd Lock to Modem Rpsd Rpsd Lock to Administratlon Terminal or Printer DTE Powering Up the Rpsd Lock Installing the Rpsd Key Connecting the Rpsd Key to the Terminal Connecting the Rpsd Key to the ModemPowering Up the Rpsd Key Testing an Uninitialized Key Power-Up Behavior of Uninitialized KeyCables, Connectors, and Ports Table PBX24Installation Aux. Port Settings Software ComponentsInitializing the Rpsd Lock Initializing an Rpsd Key Test Rpsd Lock Installation Rpsd System Administration Time of Day Access System Activity Log Fields of the System Activity Log entries are Single Point Administration Enable/Disable Block AT&T and Other Key UsersForce Connect/Disconnect Authorized Keys 6RPSD System Administration Rpsd System Administrator Command Set Add UserSyntax Sample Command and Response Without Optional Secret Key Sample Command and Response With Optional Secret KeySample Command and Response Block UserUnblock User Test User Remove UserFirst Sample Command and Response List User TableSecond Sample Command and Response User IDBlocked? Permanent?Third Sample Command and Response CR Change Restriction RestridStarthhmm Endhhmm Dayno LR List Restrictions N t aRestriction ID Start TimeUR User Restrictions LH Log History Fields of the Log History screen are AH Access History Device #Duration FH Failure History Date Time User ID Device #Reason ST Status Display LS List Statistics RS Reset Statistics FC Force ConnectFD Force Disconnect Date SetClock Set ID SetSC Set Communications Parameters Help Screens Sample Help Request and Help ResponseRpsd Key Use Rpsd Key Use Access Failure Messages Last Call Status TestRpsd Key User Command Set Set User ID Set Secret KeySet Device Number List User InformationHistory Display 08/14/90 08/14/90 131413 Date Changed OK Set Log ID Status Display RPSD/KEY1110RPSD Key Use Wipe Out Troubleshooting Troubleshooting 2Troubleshooting Access Failure Messages Check described in Testing the Rpsd Lock Access Failure Messages Code Meaning Action 6Troubleshooting Testing the Rpsd Lock Built-in DiagnosticsSelf Check Last Call Status TestHardware Replacement Modem Ring TestReplacing the PBX Modem Replacing the Lock or Key 12Troubleshooting Saving the Key Seed Value Cables, Connectors, and Ports Table Xxxxxx PBX Device LEDs Front Panel LEDs Figure B-1AT&T Definity Rpsd Table B-2 Index Index2Index Index