AT&T Remote Port Security Device user manual Test User, Remove User

Page 56

T - Test User

Syntax:

t <user_id> [ RETURN ]

Returns a seven-digit, pseudo-random code to be matched by a code from the specified RPSD Key user. This is used to check whether the RPSD Key has been seeded properly with the secret information. The Test Response on the RPSD Key is obtained by using the List User Information command on the RPSD Key user’s terminal. See Chapter 4, RPSD Key Use for details on the Key user command.

In the syntax line above, t is the command and use the List User Table command. See List User

Sample Command and Response:

<user_id> is the user ID. To check the user IDs, Table in this section.

> t KEY20

Test Response is: 8119704

>

R - Remove User

Syntax:

r <user_id> [ RETURN ]

Removes a user from the user table. This prevents that user from accessing the RPSD Lock or the attendant RMATS channel. The ten permanent AT&T users cannot be removed. If the user is added again, the user must reinitialize the RPSD Key with new secret information. The user could also be re-entered if the secret key information was retained. In such a case, the Key would not need to be reinitialized. See Chapter 2, Initializing an RPSD Key for the procedure.

In the syntax line above, r is the command and <user_id> is the user ID. When a Remove User command is issued, the RPSD Lock requests a y or an n as confirmation of the removal. To check the user IDs or whether a user is permanent, use the List User Table command.

See List User Table in this section.

Sample Command and Response:

> r KEY20

Are You Sure (Y/N) ? y

JPLock01 447 08/14/90 14:20:43 KEY20 -- User Removed OK --

>

3-10RPSD System Administration

Image 56

Contents AT&T Trademark Notice Important Safety Instructions Important Safety Instructions Part FCC NoticesPart 15, Subpart a Contents Rpsd System Administration Troubleshooting Cables, Connectors, and Ports TableRpsd Key Use Device LEDsList of Figures List of Tables Getting Started Getting Started Protection Process Rpsd Lock and Key Configuration Audience ResponsibilitiesThis Document Typographical ConventionsHotline or Other Service Call Numbers/Addresses 800Installation Installation 2Installation Power Supply Room Layout/EnvironmentLocation of Administration Terminal or Printer Hardware Components Rpsd LockRpsd Power Monitor Adapter Bypass Connections PBXs Rpsd Lock or Key Administration Terminal Rpsd Lock Administration PrinterOther ModemsRpsd Key Hardware Installation Procedures Installing the Rpsd LockCommon Rpsd Lock Configuration Connecting the Rpsd Lock to the CO Line Connecting the Rpsd Lock to the PBX Modem Rpsd Lock to Modem Rpsd Rpsd Lock to Administratlon Terminal or Printer DTE Powering Up the Rpsd Lock Installing the Rpsd Key Powering Up the Rpsd Key Connecting the Rpsd Key to the TerminalConnecting the Rpsd Key to the Modem Testing an Uninitialized Key Power-Up Behavior of Uninitialized KeyCables, Connectors, and Ports Table PBX24Installation Initializing the Rpsd Lock Aux. Port SettingsSoftware Components Initializing an Rpsd Key Test Rpsd Lock Installation Rpsd System Administration Time of Day Access System Activity Log Fields of the System Activity Log entries are Force Connect/Disconnect Single Point AdministrationEnable/Disable Block AT&T and Other Key Users Authorized Keys 6RPSD System Administration Syntax Rpsd System Administrator Command SetAdd User Sample Command and Response Without Optional Secret Key Sample Command and Response With Optional Secret KeyUnblock User Sample Command and ResponseBlock User Test User Remove UserFirst Sample Command and Response List User TableSecond Sample Command and Response User IDBlocked? Permanent?Third Sample Command and Response CR Change Restriction RestridStarthhmm Endhhmm Dayno LR List Restrictions N t aRestriction ID Start TimeUR User Restrictions LH Log History Fields of the Log History screen are Duration AH Access HistoryDevice # Reason FH Failure HistoryDate Time User ID Device # ST Status Display LS List Statistics RS Reset Statistics FC Force ConnectFD Force Disconnect Date SetClock Set ID SetSC Set Communications Parameters Help Screens Sample Help Request and Help ResponseRpsd Key Use Rpsd Key Use Access Failure Messages Last Call Status TestRpsd Key User Command Set Set User ID Set Secret KeySet Device Number List User InformationHistory Display 08/14/90 08/14/90 131413 Date Changed OK Set Log ID Status Display RPSD/KEY1110RPSD Key Use Wipe Out Troubleshooting Troubleshooting 2Troubleshooting Access Failure Messages Check described in Testing the Rpsd Lock Access Failure Messages Code Meaning Action 6Troubleshooting Testing the Rpsd Lock Built-in DiagnosticsSelf Check Last Call Status TestHardware Replacement Modem Ring TestReplacing the PBX Modem Replacing the Lock or Key 12Troubleshooting Saving the Key Seed Value Cables, Connectors, and Ports Table Xxxxxx PBX Device LEDs Front Panel LEDs Figure B-1AT&T Definity Rpsd Table B-2 Index Index2Index Index