AT&T Remote Port Security Device user manual Powering Up the Rpsd Lock

Page 37

2

3

4

5

6

7

8

20

RPSD (DCE)

2

3

4

5

6

7

8

20

Printer (DCE)

FIGURE 2-9

DB25 Connections From RPSD Lock or Key to Data Communications Equipment

Obtain further information for the specific terminal or printer in use from the documentation accompanying them.

Powering Up the RPSD Lock

To power the RPSD Lock, you need:

■the RPSD Lock Power Supply

■an AC wall outlet or an available AC outlet on the UPS. (With a System 85 or DEFINITY Generic 2, the modem is external to the PBX and should also be powered from the UPS.)

Plug one end of the power supply into the appropriate port on the back of the RPSD Lock and the other end into an AC wall outlet or an available outlet on the UPS. (See Figure 2-10.)The red Power LED on the front panel of the RPSD Lock will go on and remain on permanently while the other LEDs on the front panel of the RPSD Lock should blink three times and then settle into an Idle/Locked condition. If there is any failure of the LEDs (for example, they do not blink three times or the Power light does not come on), the Lock is defective and must be replaced. If you need to replace the Lock, see Chapter 5. A full explanation of the LEDs for both the RPSD Lock and Key is in Appendix B, Front Panel LEDs.

Hardware Installation Procedures

2-19

Image 37

Contents AT&T Trademark Notice Important Safety Instructions Important Safety Instructions Part 15, Subpart a FCC NoticesPart Contents Rpsd System Administration Cables, Connectors, and Ports Table TroubleshootingRpsd Key Use Device LEDsList of Figures List of Tables Getting Started Getting Started Protection Process Rpsd Lock and Key Configuration Responsibilities AudienceTypographical Conventions This Document800 Hotline or Other Service Call Numbers/AddressesInstallation Installation 2Installation Room Layout/Environment Power SupplyLocation of Administration Terminal or Printer Rpsd Lock Hardware ComponentsRpsd Power Monitor Adapter Bypass Connections PBXs Rpsd Lock Administration Printer Rpsd Lock or Key Administration TerminalOther ModemsRpsd Key Installing the Rpsd Lock Hardware Installation ProceduresCommon Rpsd Lock Configuration Connecting the Rpsd Lock to the CO Line Connecting the Rpsd Lock to the PBX Modem Rpsd Lock to Modem Rpsd Rpsd Lock to Administratlon Terminal or Printer DTE Powering Up the Rpsd Lock Installing the Rpsd Key Connecting the Rpsd Key to the Modem Connecting the Rpsd Key to the TerminalPowering Up the Rpsd Key Power-Up Behavior of Uninitialized Key Testing an Uninitialized KeyPBX Cables, Connectors, and Ports Table24Installation Software Components Aux. Port SettingsInitializing the Rpsd Lock Initializing an Rpsd Key Test Rpsd Lock Installation Rpsd System Administration Time of Day Access System Activity Log Fields of the System Activity Log entries are Enable/Disable Block AT&T and Other Key Users Single Point AdministrationForce Connect/Disconnect Authorized Keys 6RPSD System Administration Add User Rpsd System Administrator Command SetSyntax Sample Command and Response With Optional Secret Key Sample Command and Response Without Optional Secret KeyBlock User Sample Command and ResponseUnblock User Remove User Test UserList User Table First Sample Command and ResponseUser ID Second Sample Command and ResponseBlocked? Permanent?Third Sample Command and Response Restrid CR Change RestrictionStarthhmm Endhhmm Dayno N t a LR List RestrictionsRestriction ID Start TimeUR User Restrictions LH Log History Fields of the Log History screen are Device # AH Access HistoryDuration Date Time User ID Device # FH Failure HistoryReason ST Status Display LS List Statistics FC Force Connect RS Reset StatisticsDate Set FD Force DisconnectID Set Clock SetSC Set Communications Parameters Sample Help Request and Help Response Help ScreensRpsd Key Use Rpsd Key Use Last Call Status Test Access Failure MessagesRpsd Key User Command Set Set Secret Key Set User IDList User Information Set Device NumberHistory Display 08/14/90 08/14/90 131413 Date Changed OK Set Log ID RPSD/KEY11 Status Display10RPSD Key Use Wipe Out Troubleshooting Troubleshooting 2Troubleshooting Access Failure Messages Check described in Testing the Rpsd Lock Access Failure Messages Code Meaning Action 6Troubleshooting Built-in Diagnostics Testing the Rpsd LockLast Call Status Test Self CheckModem Ring Test Hardware ReplacementReplacing the PBX Modem Replacing the Lock or Key 12Troubleshooting Saving the Key Seed Value Cables, Connectors, and Ports Table Xxxxxx PBX Device LEDs Figure B-1 Front Panel LEDsAT&T Definity Rpsd Table B-2 Index Index2Index Index