AT&T Remote Port Security Device user manual Set Device Number, List User Information

Page 80

N - Set Device Number

Syntax:

n <number> [ RETURN ]

The Set Device Number command enters a number from 100 to 9999999 as an identifier for the RPSD Key device. Use this command when you have two or more RPSD Keys with the same user ID. The device number is associated with the Key for the purpose of identification by the RPSD Lock. This command is only used when initializing a Key in the virgin state. See Chapter 2, Initializing an RPSD Key for a complete description of the procedure which uses this command.

Enter n <device_number> [ RETURN ], where n is the command and <device_number> is an arbitrary number between 100 and 9999999 that you select to be used as an identifier for that particular RPSD Key device. Be certain not to duplicate existing device numbers. The last four digits of the RPSD Key AT&T serial number is recommended.

Sample Command and Response:

> n 12345

08/14/90 14:03:59 Device Number set to 12345

L - List User Information

Syntax:

l[ RETURN ]

The List User Information command will list the user ID, device number, and test response number for the Key.

To use the List User Information command, enter l [ RETURN ] at the > prompt of the Key user’s terminal.

Sample Command and Response:

>l

User ID: KEY20

Device Number: 12345

Test Response: 8119704

RPSD Key User Command Set 4-5

Image 80
Contents AT&T Trademark Notice Important Safety Instructions Important Safety Instructions Part FCC NoticesPart 15, Subpart a Contents Rpsd System Administration Troubleshooting Cables, Connectors, and Ports TableRpsd Key Use Device LEDsList of Figures List of Tables Getting Started Getting Started Protection Process Rpsd Lock and Key Configuration Audience ResponsibilitiesThis Document Typographical ConventionsHotline or Other Service Call Numbers/Addresses 800Installation Installation 2Installation Power Supply Room Layout/EnvironmentLocation of Administration Terminal or Printer Hardware Components Rpsd LockRpsd Power Monitor Adapter Bypass Connections PBXs Rpsd Lock or Key Administration Terminal Rpsd Lock Administration PrinterOther ModemsRpsd Key Hardware Installation Procedures Installing the Rpsd LockCommon Rpsd Lock Configuration Connecting the Rpsd Lock to the CO Line Connecting the Rpsd Lock to the PBX Modem Rpsd Lock to Modem Rpsd Rpsd Lock to Administratlon Terminal or Printer DTE Powering Up the Rpsd Lock Installing the Rpsd Key Powering Up the Rpsd Key Connecting the Rpsd Key to the TerminalConnecting the Rpsd Key to the Modem Testing an Uninitialized Key Power-Up Behavior of Uninitialized KeyCables, Connectors, and Ports Table PBX24Installation Initializing the Rpsd Lock Aux. Port SettingsSoftware Components Initializing an Rpsd Key Test Rpsd Lock Installation Rpsd System Administration Time of Day Access System Activity Log Fields of the System Activity Log entries are Force Connect/Disconnect Single Point AdministrationEnable/Disable Block AT&T and Other Key Users Authorized Keys 6RPSD System Administration Syntax Rpsd System Administrator Command SetAdd User Sample Command and Response Without Optional Secret Key Sample Command and Response With Optional Secret KeyUnblock User Sample Command and ResponseBlock User Test User Remove UserFirst Sample Command and Response List User TableSecond Sample Command and Response User IDBlocked? Permanent?Third Sample Command and Response CR Change Restriction RestridStarthhmm Endhhmm Dayno LR List Restrictions N t aRestriction ID Start TimeUR User Restrictions LH Log History Fields of the Log History screen are Duration AH Access HistoryDevice # Reason FH Failure HistoryDate Time User ID Device # ST Status Display LS List Statistics RS Reset Statistics FC Force ConnectFD Force Disconnect Date SetClock Set ID SetSC Set Communications Parameters Help Screens Sample Help Request and Help ResponseRpsd Key Use Rpsd Key Use Access Failure Messages Last Call Status TestRpsd Key User Command Set Set User ID Set Secret KeySet Device Number List User InformationHistory Display 08/14/90 08/14/90 131413 Date Changed OK Set Log ID Status Display RPSD/KEY1110RPSD Key Use Wipe Out Troubleshooting Troubleshooting 2Troubleshooting Access Failure Messages Check described in Testing the Rpsd Lock Access Failure Messages Code Meaning Action 6Troubleshooting Testing the Rpsd Lock Built-in DiagnosticsSelf Check Last Call Status TestHardware Replacement Modem Ring TestReplacing the PBX Modem Replacing the Lock or Key 12Troubleshooting Saving the Key Seed Value Cables, Connectors, and Ports Table Xxxxxx PBX Device LEDs Front Panel LEDs Figure B-1AT&T Definity Rpsd Table B-2 Index Index2Index Index